I need to wire a new system boiler, the obvious place to put the supply is with the control unit which powers the boiler. But should the FCU be next to the boiler in the same way any isolation switch would be located close the load. This would still power control unit, but also need cable coming...
Long time reader, first time poster.
We moved house about a year ago and had an EICR carried out before purchasing. Everything checked out fine but with a some C3 recommendations for improvement.
The power supply to the house comes up through the floor in the cupboard under the stairs...
Hi,
I'm hoping someone will be able to help me identify this odd plug / connector.
We bought a second hand dresser and it has a spotlight fitted. The spotlight cable has the connector shown in the pic. That connector plugs into a plug, which plugs into the wall.
I accidentally broke off...
Hi everyone,
I have just stumbled across this site and was hoping someone could help me out. I have recently bought an ebike conversion kit and battery. The battery did not come with the discharge cable to connect to the controller. I am struggling to find the right type of cable/connection, I...
Hi everyone,
I have just stumbled across this site and was hoping someone could help me out. I have recently bought an ebike conversion kit and battery. The battery did not come with the discharge cable to connect to the controller. I am struggling to find the right type of cable/connection, I...
Hi all,
I am looking to connect a two switched socket to a cable that has a three pin plug at the end (This is a cable with 3 individual cables within it i.e brown, blue and yellow/green in it). It looks really straightforward however at the back of the two switched socket, I noticed there is...
Hello everyone
I am a DIYer and I'm hoping this question will be a really simple answer for an experience electrician. But as 'you don't know what you don't know' here goes.
I am wanting to put a chandelier up in a room. I have installed a separate weight bearing ring bolt to a joist to take...
I need to run an out door supply.
However the dist board is boxed in.
There is access back entry but that doesn't help glanding a swa.
Could you gland outside to a through box them carry the same cable to the breaker?
Taking an earth leas from the conduit box also.
Hi guys, just looking for a little advice.
I have just had my kitchen done (plastered and all) and had a radial circuit set up for the cooker using 6mm cable into a cooker switch down to a connection unit. It's 32amp at the consumer unit.
I have just bought an integrated single oven to find it...
Jaystore
Thread
connection
cooker
double
hob
new
single
socket
unit
wiring
Need some ideas please chaps. Ground workers have damaged a 12V cable running to a light - so I need to put a joint in to it. Its 12v DC so only 2 cores to worry about.
So far I've considered:
Wiska Shark - the 6A version
and
The TubeTee IP68 inline connector
Are there any others I...
Hello all,
I have been asked to reconnect a motor which has a manual star delta starting knob for clockwise/clockwise operation. The motor is 5.5kw 415 delta/ 720 star 10.3 amp. I'm a bit baffled regarding the 720 star connection for starting as the supply is 415 volts, should I just connect it...
Hi
Ive just got a pitch for my catering trailer, however the trailer has a 32amp inlet and the supply is only 16amp. Ive got to start there in the next 2 days, and the earliest the supply can get sorted is 2 weeks.
Is there anyway I can run it safely for now?
Know absolutely zip about...
Hi, could I have some general advise regarding the installation of an 11kw electric kiln at my property? I would like to get an idea of what works would be required (and therefore the cost)
I have this kiln housed (unconnected) in a brick outbuilding, which has an electrical supply to it from...
I am going to quote for a job (new circuit). Problem is the 10mm water bond is under the living room carpet/furniture as there is no stopcock in the house. I know it's within 600mm of the incoming water pIpe because I connected it there many years ago. I did a quick wander lead test from the...
morning guys
What do you guys normally do for a swa supply down to a garden office- where the customer doesnt want the swa viewable inside- so swa needs to be made off outside and then cores coming into the back of the consumer unit.
I know I could use a ip65 plastic box as I have fly banjo'ed...
Hello all,
After some advice, a customer of mine has an aga and his wife has got terminal brain cancer meaning she keeps putting stuff on the hot aga forgetting it's on, sometimes even burning herself. He has come to me asking me to fit an oven and a hob for them alongside the aga so they can...
Just had a new kitchen installed. The new cooker and hob didn't come with any cable. The hob is rated at 6Kw and the single oven at 2.2Kw. The circuit is a 32A mcb, 6mm t&e to a ccu and then 6mm down to the connection unit.
MI says to use H05V2V2-F T min 90C. Is this Butyl? I was going to...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc