hob

Recent contents Top users
  1. L

    Installing Ducting for kitchen hood + Fused spur for oven and hob ?

    Hi all, I have recently had a new hood installed and need to install some ducting. I live in a flat with loft access its a 1 up 1 down. I'd like to run the ducting straight up into the loft and then out through the soffit. Can someone please recommend makes of vents, ducting to use? And also...
  2. E

    Wiring terminal block for induction hob

    Hello...I need to rewire a terminal block for zanussi induction hob zei6840fbv Can someone help please. ImGe attached
  3. B

    Induction hob.

    Am about to install an induction hob and can either use single phase or three phase. Will use singles in conduit. Maximun load is 11Kw so either single phase in 6mm or 3phase using 2.5mm. If I use 3 phase I will get a normal cooker isolation switch to operate a 4 pole contactor, as am not too...
  4. J

    Induction Hob & RCCB

    Would appreciate your thoughts on this please. Wylex split load consumer unit with one rccb, new circuit installed for induction hob on non rccb side with 32 amp rcbo. When the hob is switched on the rccb trips, not the rcbo. The circuit has been tested out and is fine and the neutral for the...
  5. N

    Advise on a new 4 wire ceramic cooker hob

    I have just bought a new cooker hob which has 4 wires however my connection points only has 3 connectors do I connect 2 of these wires together in order for it to function properly or would I need to buy a new connection point with 4 pins on. I will more than likely have to get an electrician in...
  6. A

    13amp plug for 3000w induction hob

    Hi all, I had a look around and can't seem to find anything regarding my specific issue. We use 240v We bought a new induction hob, it's a Brandt BPI-6410B and is rated as 3000w / 13amp and has wiring as below. We had a Bosch PIN675N17E/01 rated at 7200w which died. It was wired to a round...
  7. G

    Yet another induction hob question

    Hello I have a new AEG induction hob rated at 7.4kw max using power sharing but AEG do not specify a cable size or mcb rating nor will they answer the question I submitted to them by email. I think their position is that it is down to the electrician to decide. The configuration is as follows...
  8. 4

    Oven / Cooker Hob Diversity Question

    Hi, I would appreciate some views on the following issue I have. The Cooker radial in a house has been wired in 2.5mm T&E, to save the expense of a larger cable. Without boring with the detail, I cannot pull out and replace the existing cable, nor wire in a new 32A circuit using another...
  9. D

    Induction hob and oven fitting

    HI I want to fit an induction hob and separate oven. The supplier says the hob (7.35kw) needs a 30A supply and the oven (3kw) needs a SEPARATE 13A supply However a stand alone cooker with induction hob is specified as 11.3kw (which is approx 45A) and it states that it needs a 30A fuse. My...
  10. H

    Induction Hob - Safe to use existing cooker circuit

    Hello Forum, I need to replace the hob in the kitchen as it is faulty. I would like to be able to use an induction hob, so I need to make sure that the wiring and mcb on the cooker circuit is the right specification. The combination Oven (1 small / 1 Large ) has a Max load of 4.1Kw. The...
  11. D

    Using an Induction Hob and Fan over at Same Time

    Hi, I have a 1800 watt induction hob and 2300 watt fan oven. Both use 13 amp plugs. Are they using too much power to use at same time? Thanks for reading
  12. D

    Wiring For An Electric Hob

    Hi all, I've just purchased a 2nd hand hob. I thought it would be a case of simply plugging it in, but unfortunately it has no plug and needs to be wired up to some wall unit. What's the reason for electric hobs not having plugs?
  13. D

    Drilled through 30am cable powering oven and hob

    So... a bit of a faux pas happened the weekend... i managed to drill through the 30amp mains cable that goes down to the oven and hob. flashsgl - https://ibb.co/Q8Bf6jX Anyone know the best course of action short of channelling the wall out and rewiring the whole thing? Kind regards Dan
  14. Cupa

    Potential Overloaded? (Kitchen Oven & Hob)

    Popped round my old dear's yesterday. She quite fancies replacing her ceramic hob with an induction one, so I thought I'd take the oven and existing hob out to see what state the wiring is in (property built 1930s although I expect probably had a refurb at some point in the 70s or 80s, but...
  15. J

    Strange design of Induction Hob power input, advice please

    Hi, hope everyone is enjoying Easter! I have boon looking for an induction hob recently and found one on ebay for £25 and close by so I bought it, yay!. It was purchased as defective, its a 5 sone hob and the two left zones did not power up. A bit of research before purchase shows there were...
    • jaytee
    • Thread
    • advice design hob induction induction hob input please power strange
    • Replies: 23
    • Forum: UK Electrical Forum
  16. S

    Hob cable outside then in

    Evening All another odd question (I love my customers) There’s no 10mm or 6mm cable in their kitchen, apparently when it was wired there were all 13amp eco appliances. Anyway a new couple have bought it and want a 5 ring hob installed but the kitchen is done to a high standard so they don’t...
  17. S

    Install new oven & induction hob to existing circuit

    Hi All. Just a little help I need connecting a electric oven and induction hob. The existing is a 32 amp MCB in the consumer unit. A 4m run of 6mm sq t&e cable from mcb going to a 45A cooker control switch. From here a 6mm sq t&e going into cooker connection unit. I have removed the old electric...
    • Steve D
    • Thread
    • circuit existing hob induction induction hob install new oven
    • Replies: 35
    • Forum: UK Electrical Forum
  18. Cupa

    Wiring up an induction hob - wanted to sense check if what I'm doing is correct

    Hi guys, I have a new induction hob which I'd like to wire in. I have already wired in the oven and grill into the kitchen using a length of 4mm 3 core heat resistant flex and that is working fine. Back of the hob shows the following diagram: Based on the above schematic, I plan to wire in...
    • Cupa
    • Thread
    • check correct doing hob induction induction hob sense wanted wiring
    • Replies: 23
    • Forum: DIY Electrical Advice
  19. D

    Gaggenau induction hob fault - code Ci9 ADB R

    Gaggenau induction hob fault - code Ci9 ADB R Today, 08:29 PM Dear All, Does anyone have any experience of the induction hob range made by the company Gaggenau? I have a customer who has the above fault being displayed and now the hob after struggling on and off for a few months has finally...
  20. M

    Electric Hob installation

    I'm looking to install a new electric hob in replacement of my gas hob (I would have the gas hob professionally removed). I have an extractor hood and fan that I currently do not use this is hardwired into a socket on the wall, would it be possible to use this to wire up my new electric hob.
Best EV Chargers
Best EV Chargers by Electrical2Go! The official electric vehicle charger supplier.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Green 2 Go Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses Heating 2 Go
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

TrueNAS JBOD Storage Server

UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
JBOD Forums: a forum for JBOD storage server advice
JBOD Suppliers: JBOD Storage Server Supplies
Back
Top