Hi, can you recommend some short time insurance for a van?
Got my mate helping on the jobs, will be nice if he can drive
my van, for some emergency materials etc...
Just left the office in bits, stomach ache from laughing that much! We're taking on another lad due to extra workload (great times) and i've just sat in on an interview. My manager asks the question 'what's the recommended distance between detection in a corridor less than 1m wide' He shrugged...
Daley
Thread
answer
don't
electrical work
interview
probably
question
hi folks, i am about to go on an HV switching course, as a bit of a warm up, i have been given a HV Switching schedue to write. Does anyone know where i can find some info online for this as i am very new to HV operations? as a headsup?
Hi men,
Probably a bit of a stretch considering anyone who has one probably uses it. Does anyone have or know where I could get a spare strap for a Megger 1552/1500 range? I have bought a spare MFT 2nd hand but it doesn't come with the strap which is frustrating. Any ideas?
Cheers lads!
John
Probably in the wrong forum but I cant seem to post elsewhere.
I'm installing a new high-end Siemens cookers in my kitchen - a regular oven and a combination one. I've got separate spurs for each back to the fuse box via isolation switches.
The oven comes with a mains cable that plugs into...
Hi,
Went to look at a board change this morning, all seems fine, nothing untoward, only thing was on the downstairs ring the CPC continuity was higher than I would have liked.
r1 = 0.39
rn = 0.41
r2 = 1.44
I was half expecting around 0.75 ish, how far over the expected do you accept without...
can anyone help with finding out the requirmnts for working in holland i do mainly commercial/ industrial installations and im looking for a start on a site out there can anyone point me in the right direction thanks if not holland maibie somewhere else
jonybee89
Thread
electrical work
not uk
person
probably
qualifications
training
working
Hello guys
Ive got a transportable weather testing station that has mainly electronics in it with two racks of 13amp sockets for the computers to run on. The fuse board in the unit is part of the factory fit and has a 300 ma rcd protection the unit is based in a rural location with a TNS...
Hi.
I have some electrical drawings that has a MCC with 3 control panel with a 150A breaker, 50A, 20A and a hoist with a breaker of 20A all individually connected to the same bar (sum of 240). The main breaker of the MCC is 400A. Can I lower the main breaker capacity to 250A? Is there a...
Hey All,
I have a client who's about to buy up the units next door to his current warehouse, and fit it all out similar to his current warehouse and move buildings (double the size).
We currently use a pair of 5ft Fittings per aisle under his mezzanine floor but we're looking at fitting...
Hello all, excuse my bad grammar spelling etc. today i had the people from building control around to sign of my cu change
at my house,here is my question. My mum had her oven changed a little while ago and it has a design current of around 10.5 amps, the old fuse protecting was a 40 amp wired...
julianacb
Thread
breaker
cooker
isolation
oven
probably
switch
system
type
Doing some work in an old ladies house and she has asked for illuminated light switch locators at the top and bottom of the stairs as well as other key rooms in the house.
I normally use the MK ones which give a light green colour around the swich but I cannot use them this time as the lady has...
Greetings,
I'm in the Philippines and have an office full of PCs that need to run with as little interruption as possible. Power is pretty reliable here in general, but we have rotational blackouts for an hour a day at the moment due to a regional shortage caused by damage from the typhoon in...
hi i have been out to look at a shower that did not work so on arrival i check that there was voltage at the pull cord but only on the feed side and when the pull swicth was on no voltage on the load side so i change the pull cord for a new 1 and the shower workerd but then i got a call back the...
As title says new supermarket installation starting this week in Scotland with English company... So looking forward to it.. Any you guys covered supermarkets and any insight what's involved. I know probably trunking around perimeter the pipe off for your circuits and probably rows of lighting...
Hi, I got a phonecall from a client the other day, (replaced the CCU for a split loader) he says that he uses powerline adaptors to network the internet and has noticed that some of them haven't been working since the board change (says the sockets themselves are working fine) does anyone have...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.