test

Recent contents Top users
  1. Q

    Do companies contact you after passing SECTT test?

    I’ve just sat my SECTT test and passed, In the pass email it stated that companies in my area would be sent a list of people who passed the test and may be able to contact me directly, I am currently quite unsure if I will be offered an apprenticeship from any the companies I have been in...
  2. S

    EM lighting test facility

    Hi, RCBO appropriate test facility for emergency lighting? I have a car storage facility ( one corridor with 10 rooms off the corridor to store vehicles ). Planning to install the row of lighting all controlled from occupancy sensors, hoping to wire in one run of 3 core to tie in all sensors...
  3. HappyHippyDad

    Can I confirm how to test for and how to find a borrowed neutral?

    During some testing I found a N-E IR fault on the kitchen lights of 0.1Mohms. I also found a N-E IR fault on the ring sockets, again 0.1Mohms. This could have been a coincidence, but I disconnected both neutrals from the neutral bar (i.e the kitchen lights and sockets) and tested between them...
  4. E

    RCD tripping on test

    Hi, while testing the new board I installed I got to the live testing at the sockets one of the RCD's kept tripping during the loop test, the other ring tested fine so it's not the tester, the insulation tests where all good. Unfortunately I didn't have a residual current clamp meter with me, to...
  5. KevinH

    Napit Fast test EICR form query

    Has anyone on here using the Napit Fast test software for EICR's noticed that in the section "Extent and Limitations of Inspection and Testing" there is a box marked "Extent of Termination Sampling" which needs to be filled in. This must be a very recent addition, or it's been longer than I...
  6. B

    UK What’s the correct way to enter RCD’s on a split load board on a schedule of test results?

    Would entering each RCD as a line on the schedule of test results be correct? If so, what would be entered in boxes such as Zs?
  7. Z

    What are the causes of unbalance current during no load test of transformer?

    What are the causes of unbalance current during no load test of transformer?
  8. Q

    My OCPD (BS7671 Test Sheet)

    Hi, Main LVAC Board, Directly Fed from a Transformer. What do i put as an OCPD on my BS7671 Test sheet? Since I don't believe the Transformer has a BSEN number? If it Does, Where would i find this? Thanks Again! (Learning and struggling with testing! More complicated filling the sheets in...
  9. O

    Inspect and Test Question

    Hi all, Probs a simple one here but when testing a 3 phase board for ze as part of a periodic inspection plus part initial verification of a small db supplied by this board should I note the main 3 phase ze within the supply parameters section of cert and then the small db as zdb within the...
  10. V

    Test leads giving 0 ohms

    Hi, My Kewtech KT63DL has just come back from its annual calibration without any issues, but Ive just taken it to site and attempted to do the usual nulling of the leads before doing a continuity test and they keep coming back as 0 ohms which they didnt used to do. Normally i had to null them. I...
  11. O

    Getting strange reading when I test a recepticle

    I have moved back to my house i was born in some 60+ years ago. Most of the original house's electrical receptacles are 2 prong with the center screw that holds the cover plate on as ground. They all test, OK. My parents had an addition installed on the second floor sometime around the mid to...
  12. H

    304 written exam mock test

    Hi all , I was wondering if anyone here got a written mock test for 304 to share with me so I can have an idea what sort of thing to expect. TIA.
  13. D

    Stage 2 insulation resistance test

    I have installed a circuit for an oven and carried out all of the relevant testing so far. Apart from a neon on the double pole isolation switch, there is no current using equipment connected to the circuit yet as the property is empty. In this situation, would one just make a note on the...
  14. L

    landord has FAILED to supply a EICR test to a tenant : what can they do now ?

    First EICR was a 10 min drive by and tenant told "unsafe" this was 9 months after the deadline .To date the landlord has refused to get anything done about bad wiring etc etc . What would be the best route to complain , Council etc??
  15. D

    Does anyone use the UNI-T 528 test tool

    I'm wondering if anyone has used this tool. First of all I'm an automotive electrician but my work sent me on a PAT testing course and we have a DeltaPAT mi3309BT unit at work. I was thinking of buying something cheaper like this tool just to experiment with at home. I am 8 years away from...
  16. V

    Is there a way to test a SPD without spending thousands ?

    I know there are many MFT's out there which can test SPD's, but they all cost thousands of pounds, and I personally can't justify that cost which currently isn't mandated. However it would be nice to know that when I install a SPD that it will function. Is there a way of testing such a device...
  17. J

    Insulation resistance test

    Evening chaps, I've been asked to do a visual inspection, and an insulation resistance test on a fishing boat, which is working off 24v, this is a new ruling apparently, and without me signing it off as ok, the boat is currently docked, and not allowed to go out fishing. The visual checks...
  18. events-guy2020

    Portable device safety test question

    I have built a portable lighting game, and need advice on what safety testing would be needed for it to be used legally by private clients. In effect it is an enclosure with 10 sockets (only 5 connected, to 5 separate bulbs, connected to a switch), and 20 tails (only 5 connected to power). The...
  19. N

    My EICR test guy says I need to change my bathroom ceiling light to an IP65 rated.

    My EICR test guy says I need to change my bathroom ceiling light to an IP65 rated. Research says I need an IP44. The lamp is about 2.45m above the floor and about 30cms outside the side of the bath. Has he made a mistake or have I?
    • NoelRob
    • Thread
    • bathroom ceiling ceiling light change eicr ip65 light rated test
    • Replies: 11
    • Forum: UK Electrical Forum
  20. Yanman

    Electrical test on D.O.L fed straight from main panel isolator

    Hello everyone i recently got a job on replacing a BMS panel in a plant room. the NEW panel i installed except the control side of the install also feeds the mains for a few gas boilers, immersion heaters and cylinders, pumps. etc. I am going to do the testing on that and i...

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Green 2 Go Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses Heating 2 Go
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

YOUR Unread Posts

Daily, weekly or monthly email

Receive a daily, weekly, or monthly email containing a digest of new and recently updated threads.

Advert

TrueNAS JBOD Storage Server

UK Tiling Forum | Tilers Forums
UK Tiling Forum by Tilers Forums UK
Plumbers Forums | Plumbing Advice | Gas Forum
Electrician Tips from Professional Electricians
Back
Top