coding

Recent contents Top users
  1. R

    EICR Coding for (yet another) Hot Tub installation.

    Apologies in advance for yet another Hot Tub TNC-S related thread but I'm just after a few opinions after deliberating for some time on an EICR coding. EICR at a domestic property was found to have a Hot Tub installed on an outdoor patio which is slate flagstone construction, the hot tub is fed...
  2. Redvanman

    Another coding question

    So here's the scene All bonding, impedance values, RCD protection in place. 1) Inside the bathroom outside of the zones a underfloor controller has been installed with no local isolation (wired straight from the board) I am thinking that its not a code, maybe a note as the only reg i can think...
  3. jibjob

    Coding advice

    Hi Guys, Came across this the other day, a little unsure how to code, I was thinking C3 but would like your thoughts. Obviously been done like this to accomodate different makes of MCB
  4. HappyHippyDad

    My first EICR - A little help with coding required!!

    Evening all.. I have just finished my first EICR! It took a LONG time (10 hours in total - not including writing up the report which I am doing now with a cup of coffee!) There were many, many faults/problems and I have coded most of them but am stuck with 5 of them and was hoping for some...
  5. gazzamikes

    Coding for this odd one

    Been to carry out a EICR today. consumer a dogs dinner! there are two boards one being an off peak supply. bonding to the gas service comes into the 'normal' unit, water bonding goes into the off peak unit (board now dead) the board is still connected to met. Im thinking at a push a C2 as...
  6. ses

    Eicr coding

    Interesting job doing a massive eicr on a factory On a lot of the socket circuits the sockets are wired in singles in metallic trunking with the trunking being used as one of the cpc's it appears. So two things are the trunking is also being used as cpc for lighting and some other circuits And...
  7. L

    Use of cpc as a live conductor - EICR Coding

    Fella's I'm just writing up an EICR from last month, one of the findings was a lighting circuit on the non RCD side of the board where the cpc was used as a strapper in 2 way light switching, Ive marked it as C2 for two reasons, one being that there is no longer a cpc in the cable and also that...
    • LlandrilloSpark
    • Thread
    • cable coding conductor cpc eicr however insulation live practice schedule
    • Replies: 16
    • Forum: UK Electrical Forum
  8. C

    EICR coding opinion?

    Bathroom light fitting ceiling rose b/c type in zone one C2 or C3, RCBO protected, existing install designed to previous regs? thoughts appreciated?
  9. M

    Coding

    Hi all my question is, What coding is the following. 1. Lighting circuits in property rented to students, circuits chased in walls. No rcd protection. 2. All types of Circuits in a school without rcd protection. Some chased some surface. Would all above be on a c3 and safe for...
  10. L

    EICR meter tails coding

    Can anyone give me some advice on coding I recently carried out a EICR on a Commercial premises (communal areas of a block of flats) 3 x DB's all single phase with incoming 3 phase supply with 100A type 2 b fuses with 16mm tails going to each DB - personally I warrant this a code 2 any thoughts...
  11. M

    EICR coding

    Hi guys After advice doing EICR report on a welfare set up on a building site I am after advice on my coding welfare set up is on a tn-s protected by 100ma main rcd tripping out at 42.3ms at x1 I have some covector heating circuits on a c16 mcb but zs is to high for the c16 what code would...
  12. S

    EICR Coding

    I need a hand to confirm what coding goes with what please on this house I have been asked to inspect a house by an agent and this is the situation: TN-S Earthing (0.4 ohms) No CPC in lighting circuit with Class 1 fittings No Bonding to Gas or Water No Sleaving on any CPCs All CPCs twisted...
  13. kingeri

    EICR - coding for a single CU

    Been doing a few bits at a house down my street. Guy had an EICR done a few months ago (not by me). He wanted the stuff picked up on this put right. Fair enough, I thought. So I had a look through the EICR. The installation is in generally good condition, but I have spotted a few things...
  14. T

    High Ze coding on new EICR

    Still trying to get to grips with new EICR coding - got 400 ohms on earth rod all protected by 30mA rcd. What would you code this as under the new EICR?
  15. K

    Coding for EICR forms

    Hi all, I am trying to decide on coding for 2 items, and was interested in peoples input, as whether these are acceptable, or C1,C2 or C3. EICR form 4.3 - Condition of enclosures in terms of IP rating - 4.4 - Condition of enclosures in terms of fire rating - With both of the above the...
  16. O

    EICR Coding Opinions please

    Ok, so here I am testing/inspecting some new floodlights installed at a local community facility. The installers, in their wisdom scarpered without leaving anything resembling a certificate so I'm doing a EICR on the 2 circuits in question. The "post" end of the circuits is shown here, there is...
  17. 1

    Review if Electrical Installation Condition Report coding used?

    I've been asked to go and price a job based on an EICR that the client has had done. Some strange coding in my opinion but just wondering what you guys think?:thumbsup
    • 1shortcircuit
    • Thread
    • coding condition electric electrical electrical installation installation review
    • Replies: 23
    • Forum: UK Electrical Forum
  18. S

    coding for a condition report

    What code if any would apply to a circuit incorrectly marked ? For example shower marked as a cooker.Thanks.
  19. M

    non rcd sockets pir coding

    What would be the best code for sockets that are not rcd protected? No sockets are outside or near the doors so would it be a code 4? The supply is a tns with 10mm bonding to gas and water but no rcd protection to any circuits. Thanks
    • mcm
    • Thread
    • aus coding pir rcd socket sockets
    • Replies: 6
    • Forum: Australia
  20. S

    pir coding for rewireable fuse carrier with asbestos flashguard

    Looking for some help not came across this situation before, doing pir in domestic property and the consumer unit is old mem type board with rewireable fuses, some have been changed to bs 1361 fuses but the ones that haven't have asbestos flashguard in them. What code would you suggest? Thanks

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock