Hi All,
I hope you are doing well.
I am asking about the electrical wire. I am in the process of working on the floor across the 1st floor and while the decking is exposed I want to run a wire for future power shower. What wire should I use?
Thanks
Best regards
Hello
I have two new appliances
Electric oven rated at 3.95 KW
Induction hob rated at 7.2 KW
total of 11.15 KW
Currently it is on its own supply with a 10mm Twin and Earth and the MBC is 32amps
Can you please advise if the following
Cable size is sufficient ( behind plaster )
MCB Amp...
Hey!
I've got one room in the house with a wall socket. I'll be installing a new wall socket on the other side of that wall, passing an electrical cable from one socket to the other for wiring it up. I'm pretty sure the wall has some kind of insulation, should I be adding a tube or cable sleeve...
Hi. I'm being tasked with installing an electric shower into a property that was built back in the 1980's. The main consumer unit has only 4 ways and is protected by an RCD, and is fully populated and in a very tight space under their stairs. However one of the MCB's is currently used to feed...
Hi - looking for opinions please so that I respond reasonably rather than as I would actually want to.
Had a towel rail in bathroom. Replaced it with a meatier electric towel radiator to actually heat the room - I did all the calculations to get the correct wattage. Sent details to an...
Good afternoon all, today I experienced a near death electric shock. This happened on a single phase domestic property!
I was carrying out a few minor jobs for a customer: one of them was to install a new flood light to an old brick store in their back garden.
The brick store was fed via a...
Hello,
I've got an issue with my electric flat roof skylight velux: the pad reads 'no contact' with the flat roof velux. Please see attached picture. Have you come across this issue before? The plug is switched on.
Thanks very much everyone!
I'm installing a Rheem Retex-27 27kw electric water heater. While it's not required by the code where I am, I'd like to have a disconnect switch for it. It requires 3 40A double-pole breakers with obviously 2 wires for 240V coming from each, so total 6 gauge 8 wires plus ground coming to the...
Hi, I recently moved into an 1bhk flat in London, UK, and my supplier is Scottish Power(only electric). I have a "Multirate Single Phase Watt Hour Meter", with type as "5196D". There is a single display which three outputs, there are two outputs with a 1 and 2 towards the top left corner, then a...
So as the title says, I have 3 panel heaters in my flat, but only one really needs the fine control i'm after, the other two rarely go on even in dead winter as i'm stingy and my flat is small.
The heaters are mains connected (no plug sockets) so i'm looking for something that ideally will go...
There is a 220 volt electric service line crossing my empty sloped lot going to a neighbor's house. Neither the power company nor my neighbor have a written type of easement across my yard for this line. Many years ago the power company just put it there because it was easy to do. It was 15...
Electrician saw white on breakers (see pic) and says I must replace whole panel with a larger one because it’s overloaded and dangerous. Does this sound right?
Hi,
I am trying to figure out if my defy dgs906 gas/electric oven is single or 3 phase. The manual says it can be either or but the L1, L2 and L3 are not bridged so I assume its 3 phase.
I am not doing the wiring but need to pull the correct cable before the electrician comes to install as I...
I all 4 bedrooms in a rented property, there are cheap metal electric wall heaters. By design their cables are made of two wires - no cpc.They are plugged into a socket circuit with 32 A MCB.How would you code that? AThe heaters are not part of the installation, do i need to put that in the report?
Hi,
I have just retrieved a Federal Electric TB63SNT Switch/Fuse unit from a skip, it looks to be in very clean condition no rust or damage to the cabinet. The cabinet door was open and the handle/selector was not correctly positioned in relation to the acual switch activating lever to enable...
I've installed a Mira SE shower. My query.
The instructions indicate a vertical rising or a falling pipe connection. I connected in a horizontal direction.
As the shower connector swivels I can't see a reason to have it only in a rising or falling type connection position, except in the...
Hello,
I'm hoping someone can help. I've been told I have to do a electric boiler service and I honesty have no idea where to even start.
I made my feelings clear about it, but it's unsurprisingly fell on deaf ears.
Is this something that I should even be doing (only lv3 & 18th qual) first, and...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc