Hi all,
I'm planning to remove a stud wall seperating my dining room and kitchen.
On the dining room side of the stud wall, there is a double socket which I want to move about 2 feet approximately along, and onto the back wall. The wires will be coming down from the ceiling as they all do on...
I am getting ready to install a new wall oven that's about 4 ft closer to the panel than the old stove. I have about 4 ft extra cable with the new wall oven location. For code do I need to install a metal box on the wall behind the new oven location or can I run the cable that's coming out of...
Hello,
I have acquired two FOGLIO wall lamps that I want to convert from wall lights into lamps. I'm not familiar with wall lighting so first I wanted to know if this is possible and if there are any risks I should be aware of. Secondly, if it is possible, what would be the best way to go about...
Hi all.
Just a quick one if I may. I am currently about to fit 3 gang smart touch switch at my front door but owing to powering two sets of lights and an external light there is something like 6 T+E's in feeding into it. The back of the new switch is quite deep and its very busy in the box...
I'm looking at putting up & down lights onto a solid brick wall (1900 semi detached house)
What's best way practically and aesthetically to install?
Mounting each light on a junction box or making a small notch in the top of the light and running flex either clipped direct or trunking from...
Hi all,
I've installed a Tesla Gen 3 wall charger supplied by my client.
For your information, the place that I installed is in a block of flat basement where the Meter room is.
After some researching, I've fitted a Proteus board fitted with SPD and PEN fault detection device.
All dead test...
Anyone got the older MFE30? I've been offered one cheap and I'm wavering!
I like the fact it starts off sealed to the wall, and I'm doubting whether the extra 10mm would be used much.
Or did anyone have one and then upgraded to the MFE40, and would you say it's made all the difference and you'd...
HI All - need to run supply cables from the drivers to the ribbons in a new build. Its an ICF so will have min 10mm of plaster plus finish applied to what are effectively block walls. - Do i need to chase in the 12v DC supplies? and do i need to put these in conduit? - or is there a...
Hello All. I have a Westinghouse pxr6988 wall oven. It has a cutting out problem when using it in Keep Warm mode, it heats ok and stat is working. But, when I turn it off the oven goes dead, no clock etc.
The trip switch on the electrical board is not tripping. But to get the oven to work again...
Hey there! I am fitting four lights in my kitchen and have come across two issues (pictures attached - this is really the best quality I could do, sorry).
1: the light fitting takes one live (brown) and one neutral (blue) wire in a white junction that goes inside the fitting.
In two of the...
Hi, I recently installed a smart light 2 gang 1 way smart switch. The two lights in question turn on. However on one of the 2 way lights I have spotlights and only one spotlight out of 4 comes on. Previously all 4 turned on. Any advice?
Hello,
I wish to replace the old 2 gang switch pictured, with the smart switch pictured.
Am I right in thinking that all 3 reds wires would need to go in L.
Then the lower left black wire can go in L1.
And then the pair or black wires (from the bottom right) can go in L2?
Many thanks.
Hi guys I'm looking for some advice. I have recently removed a wall socket that we no longer need, and have wrapped the individual Live, Earth and Neutral wires in electrician's insulating tape, and then wrapped the end of the whole cable in insulating tape, before cementing it back into the...
Looking for advice for the following:
Bosch Induction cooktop model NIT8669SUC ) came with 3 bare wires (Black, Red, Green) but my wall has a 4 pronged 240V receptacle. I am assuming that the 4 pronged receptacle has a neutral in addition to the ground. Question: How do I connect the 3 wires to...
Ive bought a atf600 wall mount with transformer attached. Details on transformer are input 230v output 4.2v 600ma. Question is I have a unused fused spur where I want to put this could I connect it to the fused spur if so what fuse would I put in the spur.
Many thanks
Hey all,
Currently I have two wall switches that control two outdoor spotlights.
I Want to install smart wall switches.
Some require a neutral wire (Wyze, kasa, etc), a few don't (much more $)
Does this box current have neutral wires or no. Thank you in advance!
Hello.
Is it allowed to turn a 1.3" (34mm) thick 4-core (neutral and 3 phase) cable that is 7" (18cm) long, including outer insulation, at the exit from the wall by 90° like a clock hand?
If the insulations are too stiff, I could heat the piece of cable with a hair dryer.
This black cable is...
Hi Everyone, DIY advise required here please.
I have the following wall switch, currently wired in as below and controlling external roller blinds.
Inside the wall view has additional wires.
My DIY project is to replace the wall switch with a smart one below
And here is my wiring...
I’ll see if I can describe this without making a diagram.
Tomorrows job is wiring and fitting wall lights at my mother in laws, up the staircase.
There’s a U shaped stair, with a half landing. So 5 or 6 steps up, turn around, another 5 or 6 up. Top landing is an L shape around the open stair…...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.