Teeside HNC Electrical and Electronic Engineering

[Connor Mennell]

what questions you guys struggling with in particular? Just send me a message and I’ll help as best as I can.

 

[Tom morgan]

The whole thing.. I just don't understand any of it

 

[AyresomeBoro]

I am now working as a Process Operator so changed my units slightly and purchased Distributed Control Systems.

I have just submitted TMA1 of the DCS unit and to be honest for the assignment I copied diagrams and extracts from the Blackboard lessons. Some of the questions were exactly the same as the lesson self-assessment questions. Hopefully I haven't achieved a low mark for being lazy but I couldn't see an alternative way of answering. Compared to the heavy mathematics of EEP it seems way too quick and easy.

 

[AyresomeBoro]

I can help you both as I've completed just let me know in a conversation..

what questions you guys struggling with in particular? Just send me a message and I’ll help as best as I can.

Thanks guys I took a short break to start DCS but should really get EEP3 finalized, I'll be in touch soon when I read back over it. Cheers.

 

[Connor Mennell]

Thanks guys I took a short break to start DCS but should really get EEP3 finalized, I'll be in touch soon when I read back over it. Cheers.

All good man This one is a pig to be honest, the content is in the lesson notes to get you through it, but you really do need to siege through the crap for the equations/methods to answer them. Synethesis of the complex waveform took me a few weeks or researching software which could do it and I can let you know what it is etc when on it

 

[Hilldog]

I’m struggling a bit with the distributed control systems module (DCS). All the answers are pretty much in the book but it seems too easy and I’ve been marked down a bit before for short answers on the pneumatics module. I can’t find any reading material in regards to taking the answers further. There isn’t even a module reading list on blackboard. Does anyone who has done DCS module want to swap notes etc? It’s my 7th module so happy to swap notes on my other modules

 

[Hilldog]

I know what you are saying. It’s hard to not just copy from the books word for word! There’s no other info anywhere that I can see.

 

[Hilldog]

Have you completed DCS module Gizzy?

 

[GIZZY]

Have you completed DCS module Gizzy?

No sorry, was looking at it though because I need to start my next module, not sure what to go for tbh.

How is it so far?

 

[Hilldog]

It’s not too bad but as I said there’s not really any additional information that I can find that provides further background. All of the answers seem to be in the book but I’m just very cautious about copying directly. I’ve not handed anything in yet so not sure what they’re looking for really. I had a question on the pneumatics module TMA that was exactly the same as one of the questions in the earlier self assessments. I copied their answer word for word and got marked down for providing too short an answer.

 

[Rigpig]

It’s not too bad but as I said there’s not really any additional information that I can find that provides further background. All of the answers seem to be in the book but I’m just very cautious about copying directly. I’ve not handed anything in yet so not sure what they’re looking for really. I had a question on the pneumatics module TMA that was exactly the same as one of the questions in the earlier self assessments. I copied their answer word for word and got marked down for providing too short an answer.

Hi Hilldog,

Google " lessons in Industrial instrumentation " it is a free pdf . It has all the Info you require for that module.
Cheers Rigpig

 

[Hilldog]

Thanks for taking the time to get back to me Rigpig!! I’ll take a look now

 

[AyresomeBoro]

I was going to print it out and read it at work.

... 3000+ pages

 

[AyresomeBoro]

I know what you are saying. It’s hard to not just copy from the books word for word! There’s no other info anywhere that I can see.

Just to let you know mate I’ve achieved distinction for the first assignment. As I said, I basically just copied the lesson material.

Go for it ...

 

[Connor Mennell]

Anyone done PLC module. Im on TMA 04 and struggling with the Bytronic ICT3. Just can't get the accept/rejection bit working properly

 

[AyresomeBoro]

Anyone completed DCS Assignment 2, Question 5?

Using the information below, produce a set of calibration figures for the control loop TICA1945.

T11495 Range = 100 to 420 degrees c
TICA1495 SP = PV = 300 degrees c
TCV1495 = 30%



Struggling with this one can’t find anything similar in the lesson material.

 

[Joshua Gordon]

I've completed the maths bridging module and submitted my results over a week ago, how do i progress onto beginning the full HNC?

 

[Connor Mennell]

I've completed the maths bridging module and submitted my results over a week ago, how do i progress onto beginning the full HNC?

Think once it comes back as passed they’ll inform you so you can purchase your first module or you can call up the tuole admin team and ask to be enrolled onto it (easier in my opinion as they are very helpful normally)

 

[Joshua Gordon]

Thank

Think once it comes back as passed they’ll inform you so you can purchase your first module or you can call up the tuole admin team and ask to be enrolled onto it (easier in my opinion as they are very helpful normally)

Thanks, i'm going to get in contact with the admin team now!

 

[Joshua Gordon]

Yeah if anyone else gets in a similar situation as me whereby you're waiting to progress after completing the maths bridging module, send an email to the admin team, they'll immediately process you!