Recent content by Cooper_day

  1. C

    How do you charge for remedial works after EICR failed?

    We looking at two lighting circuits and one ring with low reading on insulation resistance as main issues. Basically all lights around the house needs to be investigated.
  2. C

    How do you charge for remedial works after EICR failed?

    Hello everyone, Need some advices to be fair. How do you charge for remedial works after an EICR did not pass? Are you charging on a daily rate? Thank you
  3. C

    Tesla EV charger on new distribution board

    Hi all, Will have to apologise for asking basic questions but would rather be sure. I have got an EV charger circuit to be fit in an upgrade consumer unit. The wall connector features built-in RCD Type A + DC 6mA so it is not required to install RCD type B. The board will be 100A main...
  4. C

    Become NAPIT registered

    Apparently due to the EAS scheme rules that came in to place on the 1st of September, you are now required to have an NVQ level 3 or equivalent to join a certification body. However, if you have the 2365 you could consider the experienced worker route to upgrade your current qualification to the...
  5. C

    Become NAPIT registered

    Napit didn't mention about any courses, either by email or by phone . They only said nvq lev 3 is essential or, as specify by email and correctly you bring it up in the answer above, the years of electrical experience. Rules have been tighten up since October making more difficult(and expensive...
  6. C

    Become NAPIT registered

    I called NAPIT to know what are the steps to become registered with them. I have been told I must have NVQ Level 3 as minimum or apply as experienced worker. Barely in mind I got all electrical qualifications until NVQ but not NVQ yet(City&Guilds lev.2, lev.3, 18th Edition and EAL...
  7. C

    Earth Leakage Clamp Meter

    Hi everyone, Any suggestion for an Earth Leakage Clamp Meter within a reasonable price?
  8. C

    Best cable cutter for meter tails

    Which is the best affordable cable cutter for at least up to 25mm2 copper conductor?
  9. C

    Consumer unit need to be mounted in plywood or plasterboard?

    Hi everyone, When a new consumer unit does have to be mounted on plywood/plasterboard? Does it applies for every circumstances? Thanks
  10. C

    Cordless drill - Dewalt vs Milwaukee

    Those are the model that at the moment I am looking at: M18 CBLPD-402C (Milwaukee) DCD778M2T-SFGB (Dewalt)
  11. C

    Cordless drill - Dewalt vs Milwaukee

    Which is the better cordless drill between Milwaukee M18 4.0AH brushless cordless combi drill and Dewalt DCD778M2T-SFGB 18V 4.0AH brushless cordless combi drill?
  12. C

    Bathroom light above mirror

    There is a shower
  13. C

    Bathroom light above mirror

    i IP20 might be suffice
  14. C

    Bathroom light above mirror

    Hi everyone, The light located above a sink and mirror is outside zone 2. Shall we fit an IP20 or is still recommended an IP44? Thank you
  15. IMG-20210925-WA0000.jpg

    IMG-20210925-WA0000.jpg

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock