help with unvented cylinder, cobi with dual channel hive

[cm electical]

I'd remove the connector strips from that terminal box and connect it up as a standard S plan system using wago connectors.
I'd probably feed the boiler directly from the sfcu and take a 4 core flex (L, N, S/L and E) from the boiler to the terminal box using terminal 2 to feed the external controls.

so terminal 3 in hive reciever would go to 5 in wiring centre, and 4 in hive would go to 7 in wiring centre as i said?? is that correct.
so from terminal 2 (switch live out) in boiler where would you take it to on wiring centre.
does that mean terminal 1 (switch live in) in boiler you would not need to connect a wire..
i thought the brown in the zone valves where perm lives but looks as if its the grey wires thats perm lives.


its just a head scratcher for me this one its been 15 year since i done this setup but without using a hive.

 

[cm electical]

so heres 1 with only 3 cores going back to boiler , will this work

 

[davesparks]

so from terminal 2 (switch live out) in boiler where would you take it to on wiring centre.

I'm sure I've mentioned this already but terminal 2 is the 230V feed to the external controls.
Terminal 2 at the boiler is the live supply to the external controls.
I don't know how I can make this much clearer.

does that mean terminal 1 (switch live in) in boiler you would not need to connect a wire..

Terminal 1 is switch live in, exactly what you have just written.
Again I don't really know how to make this more clear without being completely patronising.

i thought the brown in the zone valves where perm lives but looks as if its the grey wires thats perm lives.

Brown and blue are the motor, grey and orange are the microswitch.

 

[cm electical]

I'm sure I've mentioned this already but terminal 2 is the 230V feed to the external controls.
Terminal 2 at the boiler is the live supply to the external controls.
I don't know how I can make this much clearer.


Terminal 1 is switch live in, exactly what you have just written.
Again I don't really know how to make this more clear without being completely patronising.



Brown and blue are the motor, grey and orange are the microswitch.

can you just make it easy and do me a sketch of how you would do it

 

[UNG]

its just a head scratcher for me this one its been 15 year since i done this setup but without using a hive.

Not sure why this should be a such head scrataher when you can pick virtually any "S" plan diagram and substitute the the dual channel programmer with the dual channel hive

 

[cm electical]

Not sure why this should be a such head scrataher when you can pick virtually any "S" plan diagram and substitute the the dual channel programmer with the dual channel hive

 

[cm electical]

Not sure why this should be a such head scrataher when you can pick virtually any "S" plan diagram and substitute the the dual channel programmer with the dual channel hive

so at the boiler not cable goes into terminal 1, switched live in???

 

[cm electical]

Not sure why this should be a such head scrataher when you can pick virtually any "S" plan diagram and substitute the the dual channel programmer with the dual channel hive

so this should work then
please tell me yes
thanks

 

[davesparks]

so at the boiler not cable goes into terminal 1, switched live in???

As I have already said
The feed from the switchfuse goes to the boiler, only the boiler, nothing else.

Terminal 2 from the boiler is the 230V feed out to the external controls. Terminal 2 supplies power to the external controls.

Terminal 1 at the boiler is the switch live in.

There is more than one way of connecting this system but the following will work.

Run 3 core flex from switchfuse to boiler.
Connect the brown to L, the blue to N and the earth to earth.
Do not connect anything else to the supply from the switchfuse.

Using the 5 core flex you have already run from boiler to terminal box.
Connect blue to N and earth to earth at both ends.
Connect brown to boiler terminal 2 and the live supply of the controls terminal box.
Sleeve the black with brown sleeving at both ends, connect it to terminal 1 at the boiler and the boiler switched live at the controls terminal box.
Make the grey safe at both ends.

 

[cm electical]

As I have already said
The feed from the switchfuse goes to the boiler, only the boiler, nothing else.

Terminal 2 from the boiler is the 230V feed out to the external controls. Terminal 2 supplies power to the external controls.

Terminal 1 at the boiler is the switch live in.

There is more than one way of connecting this system but the following will work.

Run 3 core flex from switchfuse to boiler.
Connect the brown to L, the blue to N and the earth to earth.
Do not connect anything else to the supply from the switchfuse.

Using the 5 core flex you have already run from boiler to terminal box.
Connect blue to N and earth to earth at both ends.
Connect brown to boiler terminal 2 and the live supply of the controls terminal box.
Sleeve the black with brown sleeving at both ends, connect it to terminal 1 at the boiler and the boiler switched live at the controls terminal box.
Make the grey safe at both ends.

so what goes to 3 and 4 in the hive