Hi folks,
Just joined in the hope someone can help! - don't worry, i'll get a sparky in to do the work, but i want to understand whats needed first!
I have purchased a new workshop table saw which came with a 16 amp socket, though i was advised it would work fine off a 13amp socket with a plug...
Hi,
I am looking to fit an ip44 16 amp socket ( like the caravan connection type - three pin, round and blue ) to a lamp post we have in the garden so we can connect Christmas lights to it.
I have noticed these are commonly used on street lights in towns for the same reason. Upon closer...
Hi guys, as we know the limit under G83 is 16 amps at 230v export, does anyone know if this is capped to export to the grid or limited from the inverter under the regulations? point being if a base load of say 320 watts for instance at a house and the inverter was generating 4.0kw then only 16...
I carried out a EICR and the main switch for the consumer unit is only rated at 60 amps and the main supply fuse is a BS1361 rated at 100 amps.
Im thinking this should be a C2, what are your thoughts please.
Many thanks
Martin
A client of ours has asked us if our products have the ability to be wired into to 5 amp main system. We manufacture chandeliers, wall sconces, and floor and table lamps and have end uses in UK and Europe. We buy the parts needed to wire for UK and Europe, including sockets, plugs, cords (and...
Hi, Just getting a new kitchen fitted and there isn't a cooker ring main in place so have bought a gas hob and oven to reflect this.
But I have to fit a Cooke & Lewis MG045CL Microwave/ Grill (due to the oven housing) which has an overall rating of 3.25kw (1000w microwave output, so about...
If the appliance has 0.5 sq mm cable, the UK plug should (maybe "must" because of the wording in the Plugs and Sockets Regulations) be fitted with a 3A fuse, or 5A if high inrush.
If the appliance has 0.75 sq mm cable or above, the UK plug should be fitted with a 13 A fuse.
Before you get...
We are taking over a building after commissioning and I found this install of which a macerator is plugged in to. I wouldn’t install this way and the glands and metal clad covers are not even fitted properly so the IP rating is non-existent. I have to tackle them on the install but looking...
Hi all what would be the best option. A client has an existing armoured cable that is spurred of the living room socket via a 13a FCU, the armoured cable is then run to a shed, were they used to have a lights. Now as the shed was rotten then have taken it down to replace it. This time they would...
Hey there,
I tried posting this in the DIY forum but I'm unable to do so for some reason.
I've just moved into a new house where there are 2amp sockets in all the bedrooms. I purchased a bedside table lamp and grabbed a 2amp plug to connect it to that circuit. The 2amp plugs don't fully fit...
I have for sale the following items:
2 x 100 Amp Double Pole 10 Way Junction Box (Meter Splitter)
4 x 60 Amp 3 Terminal Junction Box
6 x 30 Amp 3 Terminal Junction Box
3 x 20 Amp 4 Terminal Junction Box.
£30 for the lot. These are all brand new and unused items, they have just been sat in a...
Sorry this is a general question but for some reason I couldn't start a new thread in the DIY section;
Anyway here's my question:
I have recently had the consumer unit in my house upgraded from an od 4 way wylex to a MK 10 way RCD split protection etc,etc.
to do this the electrician had to...
Done a eicr on a tt no rcd protection and ze of 268 ohms.
3 Radials in 2.5mm going to 32 amp mcb.
Just been plastered throughout and some type of rewire i think, the house is going through a sale and was requested by buyers solicitor.
I was going to replace cu and put sockets on three...
If I intall a 45 amp cooker isolator inside the kitchen cupboard can I come straight out of that and hhardwire into the cooker? So I dont have to install a cooker outletplate as there not.much room.behind.
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.