I’m at a house just now, the guy has decided to go off grid, got a company in to take care of all that side of things. There’s a shed outside with all singing all dancing off grid solar kit (looks like the inside of a space ship!). The company took an SWA supply from there into the property &...
Could you connect grid tie solar to a consumer unit in a shed that is fed from the main consumer unit in the house or is this not allowed due to how it complicates safe isolation?
I have a Solis 3.6 KW inverter which works well until it exceeds about 2000W when it shows "over grid voltage" and shuts down. This does not happen if something is switched on in the house which draws a large amount of current such as the immersion heater. I have a voltage meter in the house...
In the near future, I will be having my living room re-plastered. Before this is done, I am considering getting a grid switch installed to isolate three double sockets. The reason for this is that it is a pain to switch off these sockets, which are located in a built-in TV wall cabinet. Would...
This is confusing, I've ordered a few bits of this stuff, some switch modules and front plates and in the bumf on the website it says:-
Click Scolmore Introduced a new range of Click GridPro Frontplates and modules. A comprehensive range of finishes and modules available to offer ultimate...
as title, am looking for square edge grid switches.
I rewired a little bungalow and wired it for grid switches beside double sockets in kitchen due to space restraints. Have fitted out in M2 (from CEF) square edge…. But now have found out M2 don’t do grid switches in that style….. Found out...
I'm just wondering if anyone knows whether any/all of the Quinetic grid switch modules fit in a 25mm back box?
It "looks" just about ok. But if it definitely doesn't it would be nice to know!
Hello everyone, I'd like to seek your input on a matter. I'm in the process of designing the electrical connections for the following kitchen appliances:
Hob
Oven (below 2kW)
Fridge/Freezer
Dishwasher
Washing machine
Extract Hood
For the hob, I intend to connect it to a cooker connection unit...
Hello Electrical world.
Looking for thoughts and opinions. Currently planning out my kitchen re-wire for new kitchen.
I was originally planning on having my washing machine 9.1A, tumble dryer 6.5A, dish washer 8.5A on there own radial circuit. Total current 24.1A, protected by a 25A circuit...
Saying that they are not now called the National Grid, and the National Grid will now be called Western something or other
Somebody in the family gave it to me and said, 'hey, look at this' I took a glance at it and slung it back on the table saying, 'it's just a bill'
But they were adamant...
100 volts on a metal ceiling grid when measuring from the Met to the ceiling grid
Only when lighting circuit (led panels ) is on it goes away if the panels are disconnected from the drivers and left on
Each panel has 25 volts from met to screws on the back they are class 2!!
So the voltage...
My little house in Spain sits in the forest and has a little wire from the electricity supplier, 20 amps max. It's a fragile link, caught up in trees which fall down regularly.
I'm planning to renovate this house with lots of PV on the roof, and make it is independent as I can of the grid...
Hi all,
After a bit of diy advice….(I’m in the UK)
I’m trying to replace some grid switches for the washing machine from white to steel ones, and the wiring in the back of the white ones is L2 N2 at the top and L1 N1 at the bottom. Whereas the new ones only have COM at the top of the switch...
Re:Grid tied System.
Could someone advise please on the following.
I wish to install a 3 phase (input) Grid Tied system to my home (2 - 5kw).
My problem being that I'm told that a certified (SEG) Company needs to do the installation, although I know I'm capable of carrying out this job.
Plus...
Hi would anyone know if it's possible to put just one quintec grid switch into a grid where the other two switches are standard mains ? Would there be any issues with interference due to the wiring being so close ? I've tried just now to call the quintec helpline but its email only so thought to...
Hi Guys
Just seeing if anyone uses this range on regular basis:
https://hager.com/uk/products/wiring-accessories/sollysta/sollysta-white-moulded/part-m/grid-modules
Did for years but finally gone over to click full time now (definitely not based on quality, but versatility)
Reason I ask is I...
I've been asked to fit a Growatt spf 5000 es inverter which will have batteries (not sure what yet) and tied to the 230v domestic mains supply. Although I'm qualified to fit pv systems, I've never actually fitted any battery systems so not sure how they work in relation to connecting to the...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc