I was called to a job that had a dryer blow up and cause smoke damage to a launderette. Machie. Had failed due to age etc.
To Keep it brief there was no visual damage whatsoever apart from the machine that has been scrapped anyway and taken before id even seen it. i did usual tests on switch...
Hi, as my name says im just trying to do the project on my 2396, im looking into my options of cable management and on route i have stumbled across conduit rating factors p142 yellow osg (ive never worked with conduit) and the rating factors only go up to 10m, is this 10m maximum length or 10m...
2396help
Thread
cables
conduit
every
factors
inspection
lengths
meters
Hi. I'm a qualified electrical engineer and work in a production hall. I have 17th edition and currently doing inspection and testing, and annual inspection course. My question is because I work I a factory how do I get certified and if I can't how can I put the inspection and testing to good...
We have a motor starter for a 1.5kw motor that have both been out of service for around 5 years. We plan on bringing this motor and starter back into service. My question is, is there an official checklist with certification to a standard such as bs7671? For this fitness for service inspection...
Eh up :)
I don't do EICRs - not enough experience - but the things I see on some reports done by others really dismay me. Perhaps some of my understanding needs improving, I dunno. Or perhaps the CPSes have their own set of guidelines different from the sources I use? In the examples below, I'm...
Hi all
been asked to do a commercial periodic inspection I have a 17th edition and registered with elecsa
do I need any further requirements to do this job
Hello, I'm doing a course of electrician and soon i'm gone have my first 2 weeks of practise and i'm take 2 qualification 1 22-65 lvl 3 and second one is 23-92 inspection and tasting. If you can help me with some advise for a job wich i can start in my case. regards and sorry for my english.
if you can help me along on the tick sheet cheers..
these are the faults i found today..
1.Cable duct not sealed C3
2. unterminated sy cable laying on floor (not live) C3
3. Rcd for additional protection not tripping in required times C2
4 no discrimination between protective devices...
Hello all,
The Schedule of Inspection forms for an EIC offer you 2 suggestions to enter in the boxes, either a tick to say an inspection has been carried out and the result is satisfactory or N/A to show that an inspection is not applicable to a particular item.
In section 7 (consumer...
Hi all
I have a contract starting soon to test temporary supplies on a construction site.
The supplies are provided by mobile dbs with comando plugs and the supply is 110V.
Would the testing be done with a PAT tester or physically testing inside the db?
Would all circuits be 100% test...
lex101
Thread
inspectioninspection and testing
supplies
temporary
testing
Hi guys, been away off this site for ages, glad to be back. No doubt been asked many times before,but is there is a link whereby I can download EICR / EIC forms just to use as a one off.
Also as I'm very rusty filling in these forms, is there an explanation page for the Schedule of Inspection...
I have my NIC inspection on the 9th of March. Most of my work has been out of my area but I've had
a small site since November 15mins away which I had planned to take assessor to. Problem is the site has run quite a bit over due to roofing issues etc.
I will have two of the plots 2nd fixed...
Hi, my name is Craig.
I have been doing electrical for about year+ but only started college about 10months ago.
We have began the new unit of fault finding etc, and I am finding it quite difficult at the moment, and wondered if anybody had any video/reading material that is going to help me...
Just passed my 2394/5 and looking at joining napit what are the prices i should be charging?? also any advice to any new people to inspection and testing?
Hi,
I have been asked to complete an EICR on an HMO property (6 room, student rental). I have done previous installation works at the property and the electrics are in VERY GOOD condition. This is confirmed on the last EICR (which I didn't complete).
The Previous electrician has only given...
Hi there Guys
Need some help here. I came over from SA in October. I have been formally trained in testing and inspection and obtained my C&G Level 3 Electrical Installations and Level 3 building regs. I was a active contractor in SA and did hundreds of inspections and certifications. The JIB...
Peter Hartley
Thread
electrician
inspection
level
qualification
qualifications
scheme
south
testing
How do all,
Just registered with the Forum and want to get rid of that "virgin poster"
message I've just received, it's on that's probably been on a million times
so apologies, but I'd still appreciate a few suggestions. I'm a JIB registered
Installation electrician with 17th edition and...
Good Afternoon Sparks,
I am currently a maintenance electrician however I have experience in domestic, commercial and industrial installs. I am looking at completing the inspection and testing 2394 + 2395 in the next month or so as my partners job is taking us to London. So in an effort to help...
joshlobb43
Thread
city & guilds
eal
guilds
inspectioninspection and testing
professional
testing
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.