Crimping tool

[Elecmox]

I understand that good connection is desirable, but I can't afford to pay 50$ or pounds, or euros, just to crimp 2-3 wires. That's just not acceptable. I will crimp it with tool I have, or with the one I suggested to buy. I have tried them, and I am sure it will hold for longer period of time. If someone has better solution, then I will reconsider.

 

[pc1966]

If you only need a couple crimped then why not pay a local sparky or garage a couple of Euro (or a beer) to do it for you?

Spending even 5 Euro on a rubbish crimp tool for a couple of connections only does not make sense!

 

[westward10]

It is for a speaker, the ones in #11 will be fine no ones life depends on it.

 

[Elecmox]

Price for wiring two speakers is at least 15-20 euros.

Crimp tool in #11 costs 4.
Get it?

 

[pc1966]

Fair enough if that is the local costs!

 

[westward10]

Price for wiring two speakers is at least 15-20 euros.

Crimp tool in #11 costs 4.
Get it?

Get it it will do the job.

 

[Elecmox]

Thanks guys for help, I appreciate it.
I will let you know how crimping turned out in couple of days.

 

[Zerax]

Just bring the cables and crimps round to me... I'll pop them on for you... but I can't crimp bigger than 35mm^2.

 

[Timbo]

Just bring the cables and crimps round to me... I'll pop them on for you... but I can't crimp bigger than 35mm^2.

What sort of speakers have 35mm2 cables?

 

[telectrix]

What sort of speakers have 35mm2 cables?

bloody big ones

 

[Elecmox]

I tried to crimp this small wire into but connector 1.5 mm, but wire is too small and I can't crimp it good. I don't know what the size of wire is.
What should I do with the wire, should I fold it back down the wire insulation and crimp all of it?

 

[pc1966]

I tried to crimp this small wire into but connector 1.5 mm, but wire is too small and I can't crimp it good. I don't know what the size of wire is.
What should I do with the wire, should I fold it back down the wire insulation and crimp all of it?

You can fold back the conductor to crimp that with the metal part more effectively, but it is not a good idea to have any insulation in the conductor crimp section as the whole point of a reliable crimp joint is there is sufficient compression pressure to cold-weld the conductors together.

 

[Elecmox]

You can fold back the conductor to crimp that with the metal part more effectively, but it is not a good idea to have any insulation in the conductor crimp section as the whole point of a reliable crimp joint is there is sufficient compression pressure to cold-weld the conductors together.

I saw this on Crimping Small Wires - Digital Yacht News - https://digitalyacht.net/2015/03/26/crimping-small-wires/
Is this OK?

 

[pc1966]

I saw this on Crimping Small Wires - Digital Yacht News - https://digitalyacht.net/2015/03/26/crimping-small-wires/
Is this OK?

Not really. For a start they used different crimp tools - the "bad" one was not done with the correct style of crimp.

Also the red terminals should work for 0.5mm-1.5mm cable size, and if you double-back the conductor that is down to 0.25mm which is very thin, well below what is suitable for any sort of power (current rating around 2A or so). If the doubled-over conductor is not holding then it is simply a lack of crimp force!

 

[Elecmox]

Not really. For a start they used different crimp tools - the "bad" one was not done with the correct style of crimp.

Also the red terminals should work for 0.5mm-1.5mm cable size, and if you double-back the conductor that is down to 0.25mm which is very thin, well below what is suitable for any sort of power (current rating around 2A or so). If the doubled-over conductor is not holding then it is simply a lack of crimp force!

I tried to even fold wire 2x, but I just can't crimp it good, connector doesn't even hold the wire, yet alone compress it.

 

[pc1966]

I tried to even fold wire 2x, but I just can't crimp it good, connector doesn't even hold the wire, yet alone compress it.

I refer you back to the original discussion about how rubbish those crimp tools are

 

[Elecmox]

I refer you back to the original discussion about how rubbish those crimp tools are

I tried tool in #1. I can see that crimping space is higher then in tool in #11. I can buy tool #11 but I don't know if that's going to be better. Honestly, I think wire is too thin to be crimped in but connector, I might have to consider some other joint.

 

[pc1966]

I tried tool in #1. I can see that crimping space is higher then in tool in #11. I can buy tool #11 but I don't know if that's going to be better.

It will not.

Look for a cheap ratchet style tool in your local DIY or automotive accessory type shops if you want something better.

Honestly, I think wire is too thin to be crimped in but connector, I might have to consider some other joint.

Try folding the wire twice (i.e. to 4 * original thickness).

 

[Timbo]

Use uninsulated crimps, solder the wire in and use heat shrink sleeving.
Could have done them all in less time than it takes to post on here ?

 

[Elecmox]

I tried tool in #1. I can see that crimping space is higher then in tool in #11. I can buy tool #11 but I don't know if that's going to be better. Honestly, I think wire is too thin to be crimped in but connector, I might have to consider some other joint.

Use uninsulated crimps, solder the wire in and use heat shrink sleeving.
Could have done them all in less time than it takes to post on here ?

I don't know to solder.
I could only twist wires together, and use heat shrink with lighter.
[automerge]1590241197[/automerge]

I don't know to solder.
I could only twist wires together, and use heat shrink with lighter.

What diameter of heat shrink sleeve should I use with there wires that are about 1 mm in diameter ?