Bulk Workwear - Clothing Suppliers for the Whole Forum Network
This official sponsor may provide discounts for members


  1. M

    Hi I have to draw a lighting circuit that has a time clock in.... I cannot find the official symbol for the drawing anywhere . Can you help please ?

    Hi I have to draw a lighting circuit that has a time clock in.... I cannot find the official symbol for the drawing anywhere . Can you help please ? Source URL: Lighting Forum - https://www.electriciansforums.net/forums/lighting-forum.95/
  2. Floody

    Pricing just off a drawing.

    Hi Folks, this is a first for me but wondering if you could share some info. A local builder uses me to wire a few extensions now and again and he has another for me in July and needs a price. Thing is...he needs to submit the whole cost before winning the job, usually he gets me in after hes...
  3. khalid

    Electrician electrical drawings wiring diagrams for 3 bedroom bungalow thanks

    I'm new to this forum & i have electrical experience as competence person but would like to pick up some knowledge on the following anyone can do electrical drawings wiring diagrams for 3 bedroom bungalow thanks
  4. lurch

    Drawing . . free to use?

    Chaps and Chapesses Any drawing packages that are free to use that you would recommend ? Must be user friendly, I have a simple schematic I need to draw but don't need the expense.. . . . thx in advance Tony
  5. Simon-0116

    3ph star delta starter motor drawing high amps

    Star delta starter / motor problem. Starter starts runs as should on bench with no motor connected. Getting 230v to e on all 6 uvw 1s and uvw2. 415 u1 to v2 etc etc. But nothing 1 to 2s. As expected. When motor connected up. (Single speed) it takes 3a in start on all . Drops into run fine but...
  6. Leesparkykent

    Freelance CAD designer

    Does anyone know of or use someone to produce drawings for them? Need them produced for design and build jobs...Looking for a good reliable service at a reasonable price :)
  7. Sonia Norman

    2394 exam

    i took my 2394 exam tonight like a numpty I drew a tnc-s when they asked for a tN-s I did describe that it was terra neutral separate earth and still drew the wrong one! Anyone know if that's a definite fail for the whole exam. It was a 15 point question so I'm thinking I'm screwed!
  8. A

    Scales and ratios on drawings

    retraining as been out for a while ... trying to get my head around scaling and ratios on drawings .. is there a technique easy way to grasp ratios / scaling of a room ?
  9. J

    Commercial As installed drawings

    Hi guys, I've been asked to supply an 'as installed' drawing of an installation I recently carried out to include the position of the sockets/lights and mark up the EM lighting Ect... I'm no expert on CAD drawing but was wondering if there was a simple...ish program I could use to do the...
  10. S

    Am2 help!!!

    Hi all, Ive got my AM2 coming up in a couple of weeks. Anyone recently finished theirs and have any tips or what things to look out for??? Any information will be greatly appreciated.
  11. P

    Pro Solar PV Schematic System

    Hi Can anyone recommend a 'professional' system for drawing solar-pv schematics? I'm looking for something (hopefully) pre-built symbols which can assist with my systems. Thanks /Newb
  12. M


    Could anybody recommend software to create or alter fire zone drawings, and does anything exist whereas I could scan old A3 drawings and be able to alter them in the software? This isn't completely necessary however it would save a lot of time. I see that autoCAD has been recommended here...
  13. S


    Hi can anybody recommend some software iMac compatible for to edit the architects drawings, basically to add the electrical drawing details to drawing sent over?
  14. shnabz

    2365 Level Drawings

    Does anyone have the 2365 Level 3 Drawings on a pdf file they could share with me? My college have been re-using old ones and the quality is horrendous, they have probably just been printing copies of copies. They are not very good when it comes to computers and won't give me access to walled...
  15. P

    Commercial emergency lighting diagram

    Need some help if anyone can, i have been trawling the internet and forums to find a basic wiring diagram of a non maintained emergency lighting circuit with a key switch incorporated. so far i have found nothing. I DO NOT NEED IT EXPLAINING THATS NOT THE ISSUE. i find everything falls into...
  16. B

    New three phase motor winding burn out

    We have been involved in the installation of a dust extraction system which is powered by a fairly large 3 phase motor (18A). The motor was pre-wire to a control box on the side of the extraction housing and the star/delta starter was also pre-wired. The only wiring that was required was the 2...
  17. Sintra

    Drawing software.

    I need some drawing software to pull me out of a hole until I get autocad reinstalled onto my PC. Need to be able to do scale equipment layout plans and elevations. Anyone know of anything free or cheapish that would do the job.
  18. M

    heating problems

    Im currently ready to second fix my bro's heating. Its going to consist of an oil burner and a solid fuel burner and I want the oil to heat the house until the fire reaches the correct temperature and then I want the oil to switch off and the fire to take over heating the house. Please could...
  19. A

    2pir - 3light - howto?

    Hi all, Currently on a job for someone and i have had a quick think on how to do this but ive become totally BRAIN DEAD!! - Maybe its too tired.. anyway appreciate the help guys They want 3 lights controlled by two PIR's i done a drawing below one is how one is wired lol.. Now the other is a...
  20. A

    Software Needed

    I would like to know if there is a software package available to enable me to desigh/insert with my own power/lighting design onto an existing CAD layout?? Is there such a product
  21. B

    Is there a test Cert for earth rod testing

    A project engineer has requested a test cert for an earth electrode test on an industrial site earthing system is there a test cert for this? Thanks
  22. L

    Solar pv schematic

    Hi, Does anyone know where i can download a generic shematic drawing for pv installation and alter it to suit my installs. Many thanks, *EDIT* The files are now attached to the thread so no need to post your email address. CLICK HERE AND HELP YOURSELF.
  23. A

    Is a drawing register a valid instruction?

    Ok im currently up **** creek without a paddle! Ive been busy on various projects in the meen time we have had a reletively small project running in the background which i havent paid much attention to as the guys i had running it are competent and i trust them.. So after a site visit and a...
  24. N

    Kitchen Light Circuit????

    Hi All, I just wondered whether the circuit below will work: A 2 gang switch, 1 switch does the pendant, the other does the 4 down-lighters and a separate single switch for the under-cupboard lights? Thanks.
Top Bottom