Discuss Wall chaser and dust extraction in the Electrical Tools and Products area at ElectriciansForums.net
Does this fit without using tape?V tuff M class vacuum for about £120 .
DOES THE VACUUM FIT WITHOUT PUTTING PVC TAPE AROUND? AS MOST DON'T FIT CORRECTLY
Why's that matey?.....I think you need to wear ear defenders,if you keep using yours,fella
Would you be able to post a link to the items you used online? Thanks palBorrowed from a mate a hilti chaser and dust extractor for one job we did in a basement.
Excellent bit of kit, best Ive used but if £600 is too much then the Hilti is not for you!!!!
Would you be able to post a link to the items you used online? Thanks pal
Can you tell me if this is wide and deep enough for 25mm oval conduit?They’re the ones, great pieces of kit.
Should do. My chaser (erbauer) does a 30mm wide chase which snugly fits a 25mm oval conduit clip.Can you tell me if this is wide and deep enough for 25mm oval conduit?
What do you think of the erbaur? Not think it gets to heavy with having to push towards the ceiling with it?Should do. My chaser (erbauer) does a 30mm wide chase which snugly fits a 25mm oval conduit clip.
Nope, I drop it down the wall. It seems fine for a cheap tool, does the job.What do you think of the erbaur? Not think it gets to heavy with having to push towards the ceiling with it?
Even better a 2lb lump hammer, and a 4 inch bolster, chasing machine, lightweight! younger generation never had it so good, yes it's old, before you all start on me. Used to get the bus home at night covered in blood from me busted knuckles, all the Girlies looking at me thing there is a Mans Man, still times change and I suppose all you Thomas Naggy lookalikes, can't work without a Van and a Costa close by whinging about the traffic etc. never had it so good, wimps springs to mind, mind you wish I had a chasing machine, oh I did my Apprentice. In saying that, however difficult the bashing and chasing was, I always tried to balance the hard graft with the technicalities of installation work, just like I was taught by my Master, during my Apprenticeship, different today of course, sadly.You can achieve a fair bit,with a 3HP fan,some 18" ducting,and a Stihl saw...
Bloody he'll mate you sound like you've been having a right scrap with chasing them walls. Hope your knuckles are okEven better a 2lb lump hammer, and a 4 inch bolster, chasing machine, lightweight! younger generation never had it so good, yes it's old, before you all start on me. Used to get the bus home at night covered in blood from me busted knuckles, all the Girlies looking at me thing there is a Mans Man, still times change and I suppose all you Thomas Naggy lookalikes, can't work without a Van and a Costa close by whinging about the traffic etc. never had it so good, wimps springs to mind, mind you wish I had a chasing machine, oh I did my Apprentice. In saying that, however difficult the bashing and chasing was, I always tried to balance the hard graft with the technicalities of installation work, just like I was taught by my Master, during my Apprenticeship, different today of course, sadly.
Do I remember them? vividly their names, faces, the sites I worked on with them, good and valuable times.Even better a 2lb lump hammer, and a 4 inch bolster, chasing machine, lightweight! younger generation never had it so good, yes it's old, before you all start on me. Used to get the bus home at night covered in blood from me busted knuckles, all the Girlies looking at me thing there is a Mans Man, still times change and I suppose all you Thomas Naggy lookalikes, can't work without a Van and a Costa close by whinging about the traffic etc. never had it so good, wimps springs to mind, mind you wish I had a chasing machine, oh I did my Apprentice. In saying that, however difficult the bashing and chasing was, I always tried to balance the hard graft with the technicalities of installation work, just like I was taught by my Master, during my Apprenticeship, different today of course, sadly.
Well Mate it was a battle at timesBloody he'll mate you sound like you've been having a right scrap with chasing them walls. Hope your knuckles are ok, bit of scar tissue to cope with but I've has worse.
Amusing but very true Pete, I remember before I went into the office doing house bashing and doing all my own holes for fans and cooker hood using a lump hammer and comb chisel. However, the internal blocks were therolite blocks. Did you undertake a risk assessment of which knuckles you could hit?Even better a 2lb lump hammer, and a 4 inch bolster, chasing machine, lightweight! younger generation never had it so good, yes it's old, before you all start on me. Used to get the bus home at night covered in blood from me busted knuckles, all the Girlies looking at me thing there is a Mans Man, still times change and I suppose all you Thomas Naggy lookalikes, can't work without a Van and a Costa close by whinging about the traffic etc. never had it so good, wimps springs to mind, mind you wish I had a chasing machine, oh I did my Apprentice. In saying that, however difficult the bashing and chasing was, I always tried to balance the hard graft with the technicalities of installation work, just like I was taught by my Master, during my Apprenticeship, different today of course, sadly.
Reply to Wall chaser and dust extraction in the Electrical Tools and Products area at ElectriciansForums.net
Thanks for visiting ElectriciansForums.net, we hope you find the Electricians Tools you're looking for. It's free to sign up to and post a question yourself to find a tool or tool supplier either local to you, or online. Our community of electricians and electrical engineers will do their best to find the best tool supplier for you.
We also have a Tiling Tools advice from the worlds largest Tiling community. And then the Plumbers Forums with Plumbers Tools Advice.
We get it, advertisements are annoying!
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.