Was testing a 3 phase DB for storage heating. While testing I noticed I was getting continuity between 2 of the circuits, which were on separate phases. Each storage heater has its own 20A radial, and when doing an insulation resistance test between 2 of the circuits I get a reading of 0.00...
Downstairs lighting is tripping rcd.
Circuit has 4 chandeliers with multiple bulbs and led downlights in the bathroom.
Can I just test IR on 250v setting between L,N & E and expect the same results as testing with 500v.
Just done my exam, passed everything except Insulation Resistance...
I can't think how I could've failed because it isn't the hardest thing on the wrold, Tester was on 500V and I tested circuits separately.
Only way I could've failed was how I tested my Ring Final, I wago one leg of ring...
Hi Sir, I'm having a Megger MIT 1525 15KV insulation tester. During testing test voltage is not increasing more than 2KV. these is no physical damaged to the equipment. what could be the reason? pls advise.
thank you...
I had an eicr done recently, the electrician gave a C2 for the meter tails having their outer insulation stripped back too far.
Can I take a piece of the grey insulation off a spare tail and cut and glue it onto the missing piece to clear the C2? Much easier than having to strip back as it's...
Hi everyone.
I need a little advice please. Several months ago I first fixed and second fixed a timber frame loft conversion ( open plan living area and kitchen) for a friend /client. I haven't signed it off yet as I was waiting to install I new CU for him and for him to fit the kitchen. I...
Hi,
Can anyone tell me what material the main supply cable is wrapped with (I believe this cable is owned by the DNO).
My concern is whether it is Asbestos?
The below photo of the cable taken just below my cut out shows the unpainted section facing the wall to be very fibrous.
Also, another...
I have a home that is part 1940 and part 2005. The new portion is all new (well 2005 new) romex with grounds. The old is some rewired romex with grounds and some knob and tube (K&T) without grounds. Spoke with electrician and they recommended/installed a whole house surge protector and GFCI...
Hi,
Iam replacing my loft insulation to a thickness of 270mm, putting 100mm between the joists and then 270 over the top, then flooring it. I’m Putting 175mm loft legs on top of the joists which are 130mm which should give a slight air gap. My question is there is 20mm metal conduit running...
Hi there,
Does any one know what kind of insulation resistance to expect for pink fibre wall/ceiling insulation? I'm trying to figure out if the cheap insulation meter I have is actually giving me a reasonable answer.
here's a bit of background:
I have a GFCI mounted in an electrical panel...
Hi,
Just purchased a new wall light and it has no earth on terminal junction. Instructions say ‘double insulated - no earth required’.
Here is a picture:
How would this protect you if the wire from wall broke loose from this junction box and touched the casing which is metal? Or is it...
Hello everyone, I was just wondering how do you disconnect neon lights from socket outlets when doing insulation resistance test, as this will effect the readings, thanks.
Damp here this morning, and the insulation resistance on a piece of workshop equipment seemed a bit low. I could influence the reading by pressing my hands against the outside of one of its controls. That, and the fact it is getting a bit stiff to operate, show that it's time for this control to...
16mm meter tail cable has a double layer of insulation. What do all think of removing the outer layer of insulation, to make it flexible, when the cable is being run entirely in plastic trunking.
Hi all. Changing a CU in an ex-council flat, pme system, no RCD's, and initially tried to IR test whole board L/N joined to earth, got a reading of 0.28 Ohms.
Then did each circuit individually (2 X RFC, 2 X lights, 1 X cooker), L/N joined to the circuit's CPC, and got between 0.25 and 0.30...
Hi all. As I've said before, I'm not an electrician but an adult learner. I have a second hand Fluke 1653B MFT which is out of calibration but I use a CalCard to see how far out it is and it's not too bad. I've watched a thousand videos on EICRs etc and just want to increase my knowledge - if...
I'm slowly attempting to upgrade and rewire the house I'm in. Started by doing the consumer unit. Got the dno replacing my cable coming as its way past its sell by date. Got a lot of help off guys on here with what to do so thought I'd come back for some more advice
The consumer unit is at the...
Hi,
I'm installing a new shed in Brisbane made with colorbond. Obviously it will get quite warm inside so will be insulating with appropriate materials - probably foilboard. The question I have is with regards to running electrical cabling inside plastic conduit next to the colorbond and/or...
Initial fault was RCD tripping, narrowed down to a ring final cct.
IR tests on that cct with all loads removed were showing almost zero between neutral and cpc.
So I broke the ring apart and eventually found the nail through a cable, and got that all sorted.
Now its testing ok in as much as...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.