I am installing recessed lighting on a 3 way switch but neither one of the switches has a red wire. Initially I was going to try to hook up the lights to an outlet that the switches control, but it only has 1 black and 1 white wire. So when I went to the attic to try an hook up the recessed...
Hi, I'm trying to replace two 3- way switches but there are one too many wires. Can you help?
Each has a red and black wire which I've connected to the bronze screws (as they were before).
There's also a black wire that connects the black(common) screws on both switches.
But then there's an...
I have an outdoor GFCI that has never worked since I moved into my house- I thought the receptacle just needed to be replaced but when I tested the wiring with a multimeter I found that the wiring isn't energized. I suspect that the GFCI is the last outlet on my kitchen circuit because it's on...
...fortunately not connected to anything!
The black one with the red stripe has conductors consisting of 3 strands, each about 0.75mm diameter which seem to be copper. with some other metal coating. (or maybe I'm imagining the reddish glint on the cut ends...). Insulator in terrible...
Hoping someone might find this a challenging puzzle - I'd be grateful for any help and sorry in advance for the lengthy description!
I think I’ve inherited some creative wiring.
I need to replace a 3-way switch on a circuit that worked fine for years. When I removed the old switch, I found 5...
So I removed a light without having taken a photo of the set up before and now I'm having a problem reconnecting the light.
There are two light switches controlling three lights. There is one switch (switch A) that controls the light coming from the box in question (light A) and a second light...
First off, I'm clearly not an electrician and I'm sure the answer is simple, but I didn't want to go messing with the wires without being sure.
I wanted to change to a dimmer switch, so I've got some dimmable LED bulbs and a Varilight V Pro dimmer switch.
When I took the old switch out of the...
Hi all
I am after some advice I have an existing single socket with metal back box and 7 wires
3 earth to one point
2 live and 2 neutral
I have a new socket with usb that I want to swap to
I put all 3 earths in new face plate and the 2 live and 2 neutral in the correct places
Switched...
So I recently changed my light switch and thought it was OK but in the evening the lights started flickers and when I switched on one light it turned another one off in the bathroom so I presume I have done something wrong even though I though I matched it up in the same way as my old switch.one...
Hi everyone,
I've drilled a couple of screws through the floorboard as it was squeaking and driving me crazy and realised I might have done something really stupid. I've drilled quite a few screws through it and I realised the next day that I should perhaps used a stud finder to check for wires...
Hello. I am looking into the wiring loom of my 53 year old car and the fitness of the wires and connectors within. I have the two part loom that runs from the rear lights to the fuses under the bonnet out, and have been measuring the resistance of each line. Question is; what would be considered...
Hi,
I want to install a smart light switch and when I took the cover off my existing light switch I was very confused by what I saw.
New lights switch that I want to install:
here is my existing lights switch. I see the white neutral wires in the back (not in use) but what do I do with the...
Hi,
i have two electric radiators that I would like to swap. They have different lengths of 3-core wire and to be able to swap them successfully I'll have to lengthen one of the wires. I first thought about disconnecting them from the radiators, but the earth wires are soldered in (the live...
Hello. I am located in the Maryland, USA and have no real electrical experience. I just replaced my Nest video door bell with another non-subscription based brand. It went well, except that the original doorbell was tightly fit into a corner by the builder and I discovered that the new doorbell...
Trying to figure out how to properly wire an MR16 LED fixture to light given that I only have 2 accessible wires and these are both hot when the switch is enabled (using voltage detector). No neutral is available here and it's part of a series -- 3 other existing lights function when the switch...
Good day. My daughter bought an older house and wanted to change a 240 volts baseboard heater with built-in thermostat with a convectair. We bought a Convectair without a thermostat for which I wanted to hook up a programmable wall thermostat. The new convectair instructions only say to hook...
Hey there!
I removed an old wall outlet. It had 9 wires connected to it. 3 sets of white, red and black wires. I want to install a new one. What outlet do I buy and how do I make the connections? The outlet is not controlled by a switch.
Thanks
Alain
Hello. We bought a 1966 house recently. 1 outside light at our side door was old/broken so I bought a replacement. Before removing the light I used a voltage tester so I’d know which breaker to shut off. That didn’t work. I unscrewed the fixture from the wall, and found the light wired and...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.