I'm working in a waitrose changing light fittings like for like, I'm not adapting any wiring apr adding any new circuits, does a minor works cert have to be done!
Hi Guys,
Please could some tell me what qualification i would need to obtain to carry out minor works certification, i am 19 and about to become a qualified gas engineer, at present i am wiring central heating systems, from combination boilers to a fully pumped system with 3 heating zones, due...
Hi guys
Ive installed a bathroom fan, off existing lighting circuit, which i use a minor works certificate, can i get away with testing the new addition to the circuit or do i need to test the whole circuit, already rcd protected, main bonding complies with 17th edition, dont want to cut corners.
michael_brooke
Thread
ceiling
circuit
electrical work
minor
point
whole
works
Hello all, i'm new to the forum and new to the trade.
My dilemma goes as so... I'm currently in a rented property and after seeking the permission and money for parts from the landlady I am getting ready to install
a shaver socket in the bathroom (correct zone of course) and a second light...
hello all, i work for a large company so have not a great deal of experience in domestic test certificates. i have 2330 lvl 3, 2391, 17th ed ect going to do a job for some one that involves changing a circuit from an economy7 dis board to the normal consumer unit for 24/7 power! the circuit will...
just getting ready to go self employed, going to start advertising in the new year never had much involvement with cert's the full eic i have no problem with, looking at the minor works cert obviously its only for additions to a existing circuit and alterations but not for a new circuit so say...
Hi all,
Just a sanity check really but all advice welcome.
I went to survey some minor works in a 1 bed maisonette, the works the customer wants consists of light fitting replacement and light switch replacement.
Water and gas are bonded with a green 10mm cable in green, but there is no...
Smart Sparks
Thread
bonding
change
electrical work
fitting
install
light
minor
old
protection
works
was wondering when it comes to an unsatisfactory condition report, then once the corrections are made do you have to redo the form or just add a letter to it stating it is now satisfactory?
demkap
Thread
condition
factory
inform
minor
unsatisfactory
water
works
So...
If you're doing minor works on a lighting circuit (adding/moving lights) and you arn't personally chasing any cables into a wall but you've a sneaking suspicion there may be a few existing switchdrops at <50mm depth....would you insist on RCD protection?
Generally I try and RCD everything...
Hi Guys
Just been asked to upgrade shower cable from 6mm to 10mm and as not done other than when doing full rewires do i issue a minor works or a full cert
thanks
Afternoon all. Have recently installed bonding to water in each flat in a block of flats as part of some remedial work from an EICR. Need to give landlords some paperwork to say work is done, just wondered on your thoughts as to what to give to him. Seems a bit excessive to fill out a whole EIC...
Been to a property and been asked to add a socket in Bradford City Centre
Just to give you an idear of the system hear goes..
Connecting meter to DB is 10mm twin and earth with a main service fuse of 40 Amp
DB this is the first time I have seen a db like this, MCB type things but the are...
Djlelectrical
Thread
complete
eicr
electrical work
minor
needed
order
works
Ok this seems fairly simple - minor works not ok if you have to put in a new circuit right?! What if you found some lights that had no CPC in them and put it in - steel conduit - easy enough just pull single green and yellow thru, terminate and do relevant tests. But..... Minor works or new...
Hello Everyone
So basically I have just become a 2392 domestic installer after moving from Wales to England for work. I used to be a kitchen fitter until my exboss owed me 4 grand and never paid . I have studied hard and passed first time (yipee) but now I'm alone in the big bad world...
Hi - very new to this forum but having had a look at some of the previous posts - this is probably the best site for me to get some help.
I have a lighting circuit i my garage (1 light activated from 2 switches) and i need to add an additional light to this circuit. I think it is as simple as...
D_Hurst
Thread
2 way
adding
circuit
existing
fitting
help please
light
minor
please
simple
works
got a kitchen/diner knock through to do, all they want is the 2 old room lights joined and the switches made 2 way, circuit has no RCD protection at the minute it's on the non RCD side of a 16th board. all other circuits i need to work on are on the RCD side of the board
reason i'm asking is...
Took out a 6Kw shower, re routed 6.0mm cable to switched spur and ran 1.0mm to a pumped shower.
Is the overcurrent protective device for the modified circuit, the 32A 60898 breaker or the 3A fuse in spur?
Is the cable size the 6.0mm or the 1.0mm?
I am thinking it is the first in both cases but...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.