Hello there everybody
Was looking for some advice please.
Installed a power supply about a year ago for a machine- 3 phase 16amp off top of my head. I basically ran my SWA into unistrut in a 3 phase interlocking socket mounted on unistrust off the floor.
Basically the customer has now asked...
Hello guys, please can someone help, I have been asked to install a three phase point in an restaurant for a chip fryer and an oven, they have not yet purchased the equipment. So I cannot calculate the the right breaker for the job, can please someone advise what breaker would be sufficient? Thanks
Quick question got to get my six posts ,If double socket is used under counter can that satisfy regulations as isolation point or is a single pole fused switch also needed . got a tenner on it so need to know thanks for all welcomes
Afternoon chaps,
Anyone familiar with washing machines? We have a Hotpoint WF220. Select a (any) wash program, press start it starts the wash cycle but it carries on washing untill I manually stop it. The machine fill water into the drum and the drum spins at wash speed, but it carries on...
Hello,
I am sending a machine to Nigeria from Canada. This is a laminating machine and has a heater and 3 phase motor and a temperature controller. I know the temp controller will work on 50hz. The machine originates from the USA and runs on 230VAC 3phase 60hz. I am running it at 208Vac 60hz in...
hello,
i am desperatly after some help, so thank you in advance.
i am looking for a generator to power a feed auger of 18m in small mobile sheds. there would be 3 sheds wired together but with a delay, and one central plug to which the generator would be attached. this would then power the...
alec mercer
Thread
central
generator
generators
looking
machine
needs
sheds
without
Hi Lads,
Need advice on the installation of a CNC Turning Centre. The Full Load of this machine according to the plate rating is 90kva but in reality, when the machine is running, it takes a fraction of this load.
What I need is recommended cable size, fuse/breaker size. Length of cable...
Hi all i'm a little stuck been asked by my folks to have a look at their washing machine as they all think if it has a plug on it i know the whole workings, design, and how to repair it. My problem is there seems to be a short on the motor when running i know its not the pump or element as have...
jim1000
Thread
fault
insulation
machine
motor
seems
testing
washing
Anyone got any idea why [LG] washing machines with "Inverter technology" continually trip RCD's? LG insist that the fault is not theirs and that the machine I know of should be connected to a non-RCD supply to remedy the problem.
Given that most machines are in kitchens, ergo Special Locations...
Poptasticdave
Thread
circuit
don't
inverter
machinemachines
other
rcd
rcds
washer
washing
Hi,
I have a machine at work which I modified and made major changes to. As part of a college project and for work, I want to CE mark the machine.
Has anyone ever done such a thing or know how to go about it?
Gerard
Hi,
I have a socket behind a washing machine near the the open washing machine drain stand pipe. I am guessing that the pipe was blocked and the water overflowed and leaked onto the socket and blew the fuse.
The machine is new so I contacted the landlord who sent an electrician around, he...
I am rewiring a kitchen for a customer who doesnt want fused spurs above appliances (washing machine etc) Ive explained it couldnt be switched off in the event of a fault but they are having none of it . They also want a socket on the inside of a cabinet which also ive explained is bad practice...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.