UK Taking Level 2/Unit 204, 10 hour practical exam next week, need advice

[OfficialAsh]

Hello,

After my post back in 2018, I decided to take the plunge and complete the level 2 electrical installation course from City and Guilds. My local college was super helpful.

Anyway I am doing the 10 hour practical exam next week, and I am curious to know what suggestions you guys may have. I already have a photo of what we have to install. Just wanted to know what else I could do to prepare for this exam.

 

[jimmychow]

Hello,

We have a complete "pack" when we start however I am a bit dubious with the testing as it's new to me. I am starting to formulate my own testing sheet so I can "spoon feed" it to myself during the testing phase.
Attached below what we have to do and 1 of 3 testing pages I made. Is there any good websites or videos you recommend to make my testing life a bit easier? I know we have the on-site guide however it does seem a bit excessive to read when we only have 10 hours. Maybe I am just being overly ready for this.

Here is my "cheat sheet" so far:
View attachment 55244

Here is the test/circuit we have to do:
View attachment 55245

Here is what we have to test on each circuit:
View attachment 55246

Hey,

Is it possible to send me these copies please, im unable to open/access your files. I have my 10 hour assessment soon too!

Peace,

Ash

 

[jimmychow]

I have the measurements & material list will sent it over

May I please also have a copy?

Ash

 

[dappy18]

Hello,

After my post back in 2018, I decided to take the plunge and complete the level 2 electrical installation course from City and Guilds. My local college was super helpful.

Anyway I am doing the 10 hour practical exam next week, and I am curious to know what suggestions you guys may have. I already have a photo of what we have to install. Just wanted to know what else I could do to prepare for this exam.

hiya ash, i am just about to do the same exam but your photos won't load, is there any way you could resend them please

 

[rossmayhew]

I have the measurements & material list will sent it over

Would you be able to send me a materials list also please?

 

[OrangeEddie]

Hello,

We have a complete "pack" when we start however I am a bit dubious with the testing as it's new to me. I am starting to formulate my own testing sheet so I can "spoon feed" it to myself during the testing phase.
Attached below what we have to do and 1 of 3 testing pages I made. Is there any good websites or videos you recommend to make my testing life a bit easier? I know we have the on-site guide however it does seem a bit excessive to read when we only have 10 hours. Maybe I am just being overly ready for this.

Here is my "cheat sheet" so far:
View attachment 55244

Here is the test/circuit we have to do:
View attachment 55245

Here is what we have to test on each circuit:
View attachment 55246

Hello mate,

I'm just about to do the same exam as you. I just registered to this site in hope I can click the links you sent, but they don't work. I'm assuming its because the timers ran out.
Would you possibly still have the material to resend the link at all? Would be a massive help!
Thanks!

 

[mat1zx]

I have the measurements & material list will sent it over

Could i get a material list? got my exam in a couple of months

 

[Gabriel1690]

I have the measurements & material list will sent it over

Could I have that part list as well ?

 

[Gabriel1690]

Hello mate,

I'm just about to do the same exam as you. I just registered to this site in hope I can click the links you sent, but they don't work. I'm assuming its because the timers ran out.
Would you possibly still have the material to resend the link at all? Would be a massive help!
Thanks!

Did you manage to get these in the end ? I’m about to sit this exam as well , please let me know if you have them

 

[Waqas123]

Yes everything is done in singles and the metal tray and metal trunking is already placed on the test board for you, it's just a matter of lining things up to match the scale and wire things correctly, that's why I am going to take a painfully easy explanation for everything in with me so I have every aspect covered. I have attached below my line of "attack" starting at section 1, 2 and then 3.
View attachment 55249

I have a lesson Thursday so I will be going over my final thoughts with my tutor to ensure I am fully prepared but I am very confident in going forward. Just making sure I have everything covered.

Done the material listing+PPE, wiring diagram and drawing diagram.

Once I pass (fingers crossed) I will report back here with my findings and any tips I can suggest for future fellow level 2'ers!

Hi @OfficialAsh
Could you please resend those diagrams and cheat sheet if possible please i am due to do my bay assessment in February

 

[DPG]

Hi @OfficialAsh
Could you please resend those diagrams and cheat sheet if possible please i am due to do my bay assessment in February

Welcome to the forum.

That member hasn't been on here for over 3 years though unfortunately.

 

[nicebutdim]

Hi @OfficialAsh
Could you please resend those diagrams and cheat sheet if possible please i am due to do my bay assessment in February

Better idea would be to learn the skills required.

 

[Knic06]

Hello,

We have a complete "pack" when we start however I am a bit dubious with the testing as it's new to me. I am starting to formulate my own testing sheet so I can "spoon feed" it to myself during the testing phase.
Attached below what we have to do and 1 of 3 testing pages I made. Is there any good websites or videos you recommend to make my testing life a bit easier? I know we have the on-site guide however it does seem a bit excessive to read when we only have 10 hours. Maybe I am just being overly ready for this.

Here is my "cheat sheet" so far:
View attachment 55244

Here is the test/circuit we have to do:
View attachment 55245

Here is what we have to test on each circuit:
View attachment 55246

Could you send or re upload these as I am unable to access them

 

[DPG]

Could you send or re upload these as I am unable to access them

Welcome to the forum. Maybe introduce yourself and say hello.

The member you are replying to hasn't been on this forum for nearly 4 years unfortunately.