When carrying out periodic inspections we are always asked whether we have to turn off circuits with critical equipment such as servers. My stock answer is yes but I am told there is a method/meter that can carry out certain tests whilst the circuit remains live without disruption/damage to...
What a ridiculous way of rewiring lights this was.
Got L-N fault on lighting in a nursery. No lights on the entire bottom floor. With it being a nursery it's literally impossible to do anything whilst it's open because of the children. Anyway I went tonight to try and trace the fault. Every...
I had not used my B&D mini vacuum for a while, went to recharge it but the charger gave no output. Stupidly without checking the price of a new mini vac like the Vax Gator, I bought a new B&D charger but the battery would not recharge. Consequently, for future information I wondered if there...
electricans_son
Thread
battery
charger
check
checking
other
possible
without
I cant be the only one...
Just had a chap call me asking for a quote, He is apparently building 2 studio flats above his shop.
Asked him to forward me the plans to which he replied he had none - but its ok because he knows what he wants (he was on a roll now), 20 double sockets in each, a...
Basically as above I am a spark and I have my testing certs but work as a service engineer now my cousin had a new db fitted bit hurt he didn't ask me but the guy has fallen out with his tester so the install needs certification so I offered my services but I'm unsure if I can do it without...
Hi,
Just wandering what to use to get an armoured through a new duct which has been installed prior to me being on site without a pull rope.
Longest run is about 30 meters with probably 2 bends and is about 3 inch diameter but is the flexible type with ridges.
Will rods go that far and round...
Personally I think A CW SWA gland looks a lot better in a finished job without the shroud than they do with it, especially when there are 8 RGM glands in a row next to it, but does any one know of any reason why not fitting the shroud would be a problem?
The gland is indoors in a dry and heated...
Hi,
Ive fitted a couple of makes but i was wondering which of you guys prefer. Looking for good price for quality.
I know they have different types ideally i would like a make that has a good spacer to fit just in case i need to extend it out because of back box being to small
Neweys sell...
Hi everyone,
Just bought a new Permanent Magnet Alternater with up to 36V DC output. Tried to turn the shaft by hand, won't budge. Wonder if it has to be connect to a battery first. Any one come across PMA (for wind turbine) before? Cheers
Hi Guys
What determines whether a moulded 13 Amp plug requires to be fused?
I have in my hand a cable for a 72 watt transformer. one end of the lead has a physically very small moulded unfused 13 plug which is stamped 10A 250VAC. The other end is terminated with a standard moulded female (2.5...
Piratepete
Thread
13 amp
amp
cable
fuse
fuses
plugs
standard
without
A client wants 2 fans in a bathroom, one for the normal bathroom and one solely for the shower to come on when the shower is switched on. I am not sure how to wire the shower fan because if you put it on a timer the permanent live will be protected by a 45 amp MCB and not 6 amp as it should be...
I have just passed my NVQ pofolio and am just awaiting the certificate for it. I was told my my assessor that I dont need to do an AM2 because I have competed my apprenticeship but when I asked him about being JIB register he wasn't sure if I needed it. Is anyone 100% sure if I need it or not to...
Richard.davies
Thread
am2
apprenticeship
assessor
don't
register
without
Bipolar stepper motor H-bridge MOSFET output transistor burned out together with 100nF ceramic capacitor (in parallel between earth and +24V rail) and resettable PPTC fuse after someone decided to apply 110 AC voltage on dry contact input terminals. They said everything was working for couple of...
Evening all,
I'm in the midst of connecting above system, the plumber is adamant it will work without a 2 port but I'm struggling to make sense of it. I've got a system boiler with s plan and a single zone UFH manifold. Could anyone please give me some pointers re wiring without the back feed...
Hi Guys,
I need to replace my halogen security light fitting with one that is LED and also comes with PIR.
As this is a swap, am i allowed to do this myself based on current regulations?
If so can you recommend a good security light fitting with PIR? I have looked at a few online and went on...
rs6mra
Thread
earthed
fitting
light
lighting
replacing
security
without
Hi all,
I will be looking into getting assessed for the first time in the next few weeks, and as i have not previously obtained qualifying supervisor title to my list of credentials i am a little in the dark with it all. I have applied for the full scope certification and have experience in...
Ian Holdham
Thread
advice
assessment
becsa
certification
competent
cps
doing
napit
person
scheme
tips
without
Hi all
I have a house where all the circuits meet the Max Zs for that circuit yet the lighting circuit is testing as 747 ohms Zs
It looks like it used to be a TT system and been converted to a TN-C-S system. As its also got an main tcd before the board. Could this somehow be causing this high...
Maxstone89
Thread
circuit
circuits
high zs
lighting
lighting circuit
other
without
After seeing Anthony's posts today I would add this guys, if you practice Domestic installation work them to be competitive and to get on you need to be in a scheme, yes, yes I know they stink, but a lot of organisations now insist on them, there is a very strong chance you will not get work...
Hi guys, I have been asked to install some additional sockets for a family friend. However when I have been to look at the house (1950's built) I have found that the upstairs walls are really thin. They look like breeze but are much softer (I can pratically scrape them away with a screwdriver)...
iamjon
Thread
block
installing
kitchen
socket
sockets
through
wall
walls
without
I came across this LINK on Wikipedia the other day, since then I’ve done some googling and found out this is a known fact that if relay hasn’t got a diode fitted, this might/will cause a spike and might damage something on the Elise S1 circuit.
I copy~pasted this form google
"Since an...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.