HI I am looking at a job where the CU needs an upgrade as its plastic and has no spare ways for the circuit I will be installing. Looking at giving customer options so will be quoting for metal CU, integral SPD and looking at combined RCBOs and AFDDs for each circuit, looking at the spec for...
Hi need a bit of help!
Not wired one of these before, it’s an spd type 2 that’s come with board (fuse box)!
Question is does the line from the spd connect in same bus bar connection on main switch???
Hi everyone, hope everyone is doing amazing and getting through this crazy time We’re living through.
So I want to see if I’m missing something here, axiom now have a 10 way dual RCD consumer unit With integral type 2SPD at a cost of £120.
They also have a 12 way dual RCD high res consumer unit...
Hi everyone ,
Only my second post and hoping to get some information on installing an SPD Type II incorporated within a new consumer unit upgrade I will be doing next week.
With the new 18th edition regs I’ve been generally installing RCBO consumer units with integral SPD as standard .
The...
I'm about to rewire an empty house, with no electronic equipment or anything else plugged in or installed. Does this mean I can omit installing an SPD because the value of the equipment that could be damaged is less than the price of installing the device?
"For all other cases, a risk...
Hi Everyone.
Sorry if this has come up time and time again.
Soon to be installing a 3 phase submain and DB to very large garage with living annex above and lighting the external etc. (Domestic Dwelling).
Trying to get my head around this SPD jargon.
TNCS system, will i need to install a SPD...
Morning all,
I’m hoping someone could give me some advice on what’s the correct way or the done thing when fitting an spd.
I’ll be fitting a new Hager 40 way consumer unit to my house following an extension and I’ve been out the loop a bit with the domestic side of things over the past few years...
Hello,
I need to install a type 1+2 SPD into the main panel of a small business building, which needs lightning protection.
The main breaker in the main panel is a 4 poles 40A MCB.
I was looking for a SPD and I found this: Schneider A9L16634.
In the technical specification sheet it says...
The consumer unit was only installed last year to 17th edition Amd 3 & now the customer wants a SPD fitted after a friends £2k TV got fried by a lightning strike.
As MK do not make SPD, can you fit another brand of SPD in the consumer unit.
I know the rule about mixing brands of MCB/RCBO in a...
I have a problem with lighting protection in a charity in Zambia. The earthing is TT, i.e. earth pits or rods are provided for almost every building. I have measured the resistance of these and some are half to one ohm. But others are 100 ohm which is is dreadful and we are redigging these...
Looking around I'm wondering if I'm going mad. Would have thought type 2 spd next to main switch and type A (not type AC) rcd/rcbos would be the standard everyone should be looking for now (even if it's just recommended and not strictly required in domestics). But only Wylex and Schneider seem...
Came across this today. Could this damage & unit failure have been caused by a surge? Normally just see the panels go red but have never seen the burn marks.
Evening all
Is anyone fitting surge as standard in domestic property’s?
We are based down in Dorset which has 3 different flash density’s!!
So I always base is on worse case with most of our stuff being in urban areas and always unable to confirm length of supply cable! My calc is usually...
Going to be doing my first SPD board next week, single module SPD and 32 amp MCB before the RCD protected circuits.
Can I ask how and where you are recording these on the EIC?
I would probably record the mcb as a circuit as usual labeled spd but unsure what I need to record about the actual spd...
Hi all, I haven't done domestics for a while and have been asked to install an 18th edition CCU to a small terraced house ( 2 floors Ground and first). I been told that I need to install a SPD? Can someone confirm this is the case and are there any exceptions. Haven't done my 18th but will be...
Hi Guys just reading this link & thought someone might be interested
Practical tips for installing surge protection devices in low voltage panel | EEP -...
I've got my annual Stroma assessment next week and the job I am taking them to is a board change. I have not fitted an SPD as by my calculations it was not a requirement (plus a tight customer would not want the extra cost)
I don't think it will be a problem but am just looking for reassurance...
Somebody asked about a month ago if i had a picture of the SPD Board Hager do. Cannot seem to find the thread, anyway i have just done my first one since. Pictures attached.
Quality make of board, really solid.
I know its not the neatest, i do one cable at a time instead of all CPCs, then Ns...
As per the title, if you were rewiring a small house to be rented out would you, or should you fit an SPD?
Doing one soon and been screwed down on price a bit further than we would like ideally. However we have a quiet few weeks until a couple of bigger jobs start and it's local and empty...
Priced a job to change old 3ph board from pictures alone. No the firm so jobs good.
Get there and situation is no spd fitted on existing. So I was going to fit one to my new db in trunking at side of board fed of 32a breaker.
Will this act / cover / work for the whole site.
Layout is main...
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.