Discuss 24volt DC power supply for defibrillator in the Electrical Tools and Products area at ElectriciansForums.net

Looks ok to me.

You could save a few quid by not using RS though.

PSUs can be had from your local wholesaler.

What does the manufacturer state? Obviously it needs to be 100% reliable in this case.
 
Hi LeeH,
I asked 3 local wholesalers to quote and the cheapest was Edmondson's at £54+VAT.

The manufacturer's specs are;
10A/30mA Circuit Breaker
24VDC/75W Class 1

Must be earthed.

And that is all it states.
Yes, it needs to be 100% reliable as this is hopefully a life saving piece of equipment. The local community centre have managed to raise the funding for 6 of these, to be installed on various buildings around the town. I doubt I will get to install all of them, but looking like I will have at least 3 to do.

Thanks
Jon
 
Hi LeeH,
I asked 3 local wholesalers to quote and the cheapest was Edmondson's at £54+VAT.

The manufacturer's specs are;
10A/30mA Circuit Breaker
24VDC/75W Class 1

Must be earthed.

And that is all it states.
Yes, it needs to be 100% reliable as this is hopefully a life saving piece of equipment. The local community centre have managed to raise the funding for 6 of these, to be installed on various buildings around the town. I doubt I will get to install all of them, but looking like I will have at least 3 to do.

Thanks
Jon
You can't guarantee that it won't ever fail.
If you want 100% reliability you might consider a dual redundant system. Two PSUs diode gated.
That would improve the odds. But it won't protect against mains failure, a lightning strike or other catastrophies.
 
The above would not be 100% reliable...i would say that the most reliable means would be a wind-up unit...and that,would probably get 98% :)
 
A town up the road,had one in their precinct which was stolen after 3 months :(

I have little time for those who would do this,and less,for those who would purchase a chorred item of medical equipment.
 
Me Bird has a shop, and the local First Responders have had a defib installed there.I don't know who did it, but it's not actually connected to power. We know this because a car went through the shop front, damaged the socket it was supposedley attached to, and there it was just coiled up. I've had to use a defib "in anger" with the RNLI, about 3 weeks after my Dad died from a heart attack,that's not a sympathy clamour, just the facts. Our Casualty, flickered several times, we had him actually beating, but he was on a boat, we got to him 30ish minutes after the shout, onn the beach helicopters, he didn't realistically have a huge chance, but we did manage to get a bit of life, though not enough. The practical in me says, " If we'd resussed, wou;d he have been happy?, No, alive but ----ed. My chest presses were "impressive", that';s from the Rescue 104 medic, not my other half.
 
Hi,it's Romanes for "stolen".

Romanes,is the Gypsy spoken language,derived in part,from Hindustani.

You will have used lots of these words,without knowing,such as "mush" or "moosh",for "man".

Growing up with,and around these folk,has given me more than several benefits ;)

Cushti bok
 
Hi,it's Romanes for "stolen".

Romanes,is the Gypsy spoken language,derived in part,from Hindustani.

You will have used lots of these words,without knowing,such as "mush" or "moosh",for "man".

Growing up with,and around these folk,has given me more than several benefits ;)

Cushti bok
I should have guessed that from the context......:)
 

Reply to 24volt DC power supply for defibrillator in the Electrical Tools and Products area at ElectriciansForums.net

Similar Threads

Hi, I am tasked with switching some special FX kit we have over to 24v ac, from 12v dc. Purely to achieve longer cable runs with lesser volt...
Replies
26
Views
9K
3
This is my first post take it easy on me:charming: I am building a single story timber frame workshop. its going to be timber clad also. The...
Replies
4
Views
2K

Electricians Tools | Electrical Tools and Products

Thanks for visiting ElectriciansForums.net, we hope you find the Electricians Tools you're looking for. It's free to sign up to and post a question yourself to find a tool or tool supplier either local to you, or online. Our community of electricians and electrical engineers will do their best to find the best tool supplier for you.

We also have a Tiling Tools advice from the worlds largest Tiling community. And then the Plumbers Forums with Plumbers Tools Advice.

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc
This website was designed, optimised and is hosted by Untold Media. Operating under the name Untold Media since 2001.
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock