Advice on Cooker hood fuse access to replace

[Midwest]

I'm gonna have to change my name to Kevin, it seems.

 

[Hans]

Forget about breaking in from outside, just do as neat a job as you can on the coving and reinstate later. It's unlikely to be a "Clyde-built" installation anyway, I agree...so probably no screws in there, and probably the chimney will be shy of the ceiling once you remove the coving. Get it off, rewire it in a sensible, accessible fashion, make good and the job's a good one.
Good advice about the ladder too...and FFS do NOT stand on the hob!

Many thanks for the kind advice.

I wont lean on the hood or stand on hob.. Promise

2 questions please :
What is the best tool to use to cut the caving ?

I dont want to run into simliar senario again in the future , to cut and redecorate.
What do you thunk the best thing to do to avoid that even if i decided to install a new cooker hood . This is one about 8 years old . No cutting or decorating in the future for any simliar issue .



Do i need to replace the ducting or reposition it ?

 

[Hans]

Forget about breaking in from outside, just do as neat a job as you can on the coving and reinstate later. It's unlikely to be a "Clyde-built" installation anyway, I agree...so probably no screws in there, and probably the chimney will be shy of the ceiling once you remove the coving. Get it off, rewire it in a sensible, accessible fashion, make good and the job's a good one.
Good advice about the ladder too...and FFS do NOT stand on the hob!

Many thanks for the kind advice.

I wont lean on the hood or stand on hob.. Promise

2 questions please :
What is the best tool to use to cut the caving ?

I dont want to run into simliar senario again in the future , to cut and redecorate.
What do you thunk the best thing to do to avoid that even if i decided to install a new cooker hood . This is one about 8 years old . No cutting or decorating in the future for any simliar issue .



Do i need to replace the ducting or reposition it ?

 

[telectrix]

best tool is a multi tool like this:

https://www.amazon.co.uk/Apollo-Osc...TF8&qid=1521373194&sr=8-4&keywords=multi+tool

a lot cheaper than a pro unit, but will do for light DIY. once you have sorted the problem, I'd re-drill the screw holes to be outside the coving if you need to remove in future.

 

[Hans]

Forget about breaking in from outside, just do as neat a job as you can on the coving and reinstate later. It's unlikely to be a "Clyde-built" installation anyway, I agree...so probably no screws in there, and probably the chimney will be shy of the ceiling once you remove the coving. Get it off, rewire it in a sensible, accessible fashion, make good and the job's a good one.
Good advice about the ladder too...and FFS do NOT stand on the hob!

I just wanted to say THANK YOU VERY MUCH .You were absolutely spot on . No screws on the chimny after removing cutting mastic arround the caving .

I m very gratful to you for your help and advice as I manged to fix it and its now fully working order . However i m will be looking for a new one in the near future.

 

[DPG]

Nice one!

 

[Hans]

Run a cut round the mastic. There may be a screw on each side covered by coving, or with luck Kev has left them out and the stainless steel cover will be able to be wiggled off. The cover normally butts onto the ceiling rather than through it. Be careful, as you'll be up a ladder etc and you can't lean on that cooker hood too much . Hopefully underneath the cover will be a nice bit of ducting going up and out and the missing cable going into a switched fuse connection unit. Change the 3A fuse and reinstate. I mentioned the possibility of exposed wires just to remind that Kev may not have done a good job on that bit.

Many many thanks for your help . I manged to fix it and its now in fully working order . Kev left it with screws just relying on mastic.

Much obliged to you for help and support you gave me on this matter .

 

[Hans]

Hi guys

I just thought to drop you all a line to thank you for your support and valuable advices. Its highly appreciated and i m happy to say that with your help , i manged to fix it and its working now .

I ll be looking to get a new one in tgenear future though, so feel free to advice me on a good one.

Warmest regards