Todays PIR

[ian]

Cheers lads, to be honest I was a bit reluctant to reporthim…basically I never have reported anyone before, but as I see it he willstill be out there doing the same shoddy, and dangerous work, he is alsotarnishing the name of honest hard working sparks who do a good job….its really****ed me of especially leaving the covers of the tail blocks…… there arekiddies running about in this house.

Anyway, you have reassured me that reporting him is theright thing to do, will be on the phone tomorrow.

Ian

 

[telectrix]

hope you took a few photos.

 

[sparks_114]

I would do him a favour and the wider public by reporting him. I too am not the type to moan overtly about others' work but if the standard is so low to give rise to very real danger then you really have no option but to report him. As telectrix mentioned, I hope you took a few good (or a rather good few) photos. An remember the old saying: "Crappy installs prevail when good sparks fail to act"

 

[72-van]

I dont know how some people sleep at night ...

I am sorry but loadsa photo's elecsa and perhaps the local trading stds guys ..

way way way out of order in my humble opinion at least the home owner is now aware of the situation and can wear rubber gauntlets and thick welly boots.

What is the legal min south of the border for a CU change,

 

[steamboatwilly]

I would do him a favour and the wider public by reporting him. ....

That's the bottom line I think. Stunning that this is still happening. I've just been working on a house which had a bare live tail alongside the meter. this house has just been sold so where was the legal check usually done by solicitors? No certificate and dangerous installation.....brand new.

 

[IQ Electrical]

Inspected a house today and why its not a pile of ashes is amystery to me. The CU had been changed about 6 weeks ago by a spark and theclient was not given any cert etc. Since the CU change there have been“problems with the RCD tripping” and could not contact the spark that installedit.

Here are the highlights of my inspection.

• No bonding,
• 3 ring CTS not formed properly, spurs from spurs etc and no continuity on ring conductors.
• No earths at most of the lights.
• Cooker switch directly behind hob and was charred and black.
• Holes in the top of the OS socket boxes and the water poured in. (Tripping either RCD or MCB randomly)
• Broken OS lights.
• 10kw shower wired in 4mm T&E protected by a 40 amp CB.
• Loads of broken accessories where you could get 2 or 3 fingers in.
• Induction Hob wired in 2.5 T&E serviced via a 40 CB
• Garden lights were wired in T&E and the cables were scratched into the soil, probably around 30mm below the surface, and connector block taped joints. When they switched them on it tripped the MCB…. wonder why?
• Down lights covered in 200mm of insulation. Some cables are starting to deteriorate because they have been placed directly beside the lights.
• A couple of down lights wired in bell wire…..yeh, I said bell wire.

In the in the time old tradition of saving the best to last,

• The 100 amp tail blocks had no covers on them.
• Couple of the lighting circuits could not hold the RCD, so they were switched over to the non-RCD protected ways…ingenious.

As I said previously, the CU was changed a few weeks ago,apparently he is a DI with elecsa. Should I report him…..i think I should.

You absolutely must report this, not only is this guy leaving installations in a dangerous condition but he's also stealing work away from legitimate contractors by omitting work that they would have to include in quotations!

I would send a report to the scheme provider and a copy of all correspondance to trading standards, specifically asking that you are kept informed of proceedings.

 

[brightspark66]

I wonder how some people sleep at night !!!!!!!!!!!!!!!

 

[darking]

I think public hanging for the first offence! That way there is no repeat of the offence

 

[DurhamSparky]

report him ASAP....!!

im following on from a "struck off" NICEIC contractor into a house on Monday to carry out a PIR on his shoddy work! (he no longer registered with any scheme and currently getting shafted by the NIC for logo infringement after he was booted out months ago..)

 

[tony mc]

Hi Ian

Did you contact Elecsa re this job Im sure lots Of people on the forum would be interested in what they said or do ect.!!!!