Potential overload of ring mains

Post new thread
Search the forum,

Discuss Potential overload of ring mains in the UK Electrical Forum area at ElectriciansForums.net

C

Callcom

-
Reaction score
6
At a house viewing I saw a dozen electric radiators connected mainly by plugs into wall sockets, one or two (in bathrooms) connected to fused spurs. I calculated nearly 14Kw and I'm given to understand all these rads are connected to either of two ring mains with 32A breakers.

A quick look at the consumer unit showed all the powerful stuff on dedicated circuits, apart from washing machine, tumble dryer, dishwasher, steam oven, so these must be plugged into one or other of the two ring mains. There was no dedicated circuit for the electric rads.

I know you can have unlimited sockets for a floor area > 100m2, but I would have thought all those rads on a cold winter's day would cause tripping? I'm looking at having to re-wire if I go ahead with the house, unless anyone disagrees?

Cheers
 
wirepuller said:
You'll need to investigate further, assuming the rads are on stats then some diversity may possibly be applied. It would be usual to have an electric heating system on dedicated circuits though, not on a ring for general use.
Click to expand...

Thanks guys, seems like my sinking feeling is justified. Funny thing is all the rads have moulded plugs so they are designed to plug in. It's going to cost a fortune to run a dedicated service I would have thought right round the house.
 
Murdoch said:
I think you need more info ............ some of those wall mounted heaters are only 750w each!
Click to expand...
Yes I saw some of them were lower than that, and then some a lot higher. I reckon they all add up to around 14Kw and are not on a dedicated circuit, and since they plug into wall sockets they must be on one or other of the ring mains, hence my concern.
 
Billsays said:
Got to be the most Expensive way to heat a house......Can central heating not be installed? (Gas or oil) If not maybe install economy 7 heating?
Click to expand...
Unfortunately there's no mains gas. To install an oil tank and boiler plus a full system is going to cost thousands I would have thought.
 
Callcom said:
Yes I saw some of them were lower than that, and then some a lot higher. I reckon they all add up to around 14Kw and are not on a dedicated circuit, and since they plug into wall sockets they must be on one or other of the ring mains, hence my concern.
Click to expand...
Not ring mains any more Callcom, Ring Final Circuit, RFC for short, not to confused with a Radial Final Circuit.
 
It is unlikely to cause tripping of the mcb due to the diversity of the loads, however it is a pretty poor setup.

How well insulated is the property? Improving the insulation may reduce the amount of heat input required and thus reduce the problem and your electricity bills.
 
Back to the OP:

Is this a house you are thinking of buying?

If so commission a local decent spark to do an EICR and don't be fobbed off with a drive past sub £100 report. A decent report, in your area is going to cost £150 upwards and take half a day or more.

You could specify, that the EICR looks closely at the electric radiators too, so you can get decent information too.

You never know, there could be a 2nd fuse board and the "old" storage heater circuits have been used.
 
davesparks said:
It is unlikely to cause tripping of the mcb due to the diversity of the loads, however it is a pretty poor setup....Hi Bills )
Click to expand...
Diversity produced by thermosts is OK , until
they are all synchronised by a Thermal effect ,like turning off
for a few days holiday -(with no background heating) .
Then coming back whens its cold and switching them all back on at same time (Just like a power cut)
 
Well, Christmas over, with a house full, immersions on, all heating turned up, two ovens on etc etc, and not a hint of a problem. So I guess I'll just go with it for the foreseeable until and unless anything does happen. Bearing in mind we've had a few cold snaps, including the last couple of days, I'm optimistic that my concerns were unfounded. Thanks to all who took the time to reply.
 
If you want to do some checking by yourself, you could get a cheap clamp meter like this LAP Digital Clamp Meter 600A - https://www.NoLinkingToThis/p/lap-digital-clamp-meter-600a/8906f
and keep and eye on what the actual load of each circuit is.
 
Had a look at clamp meters, great solution except you can only clamp individual conductors - apart from a Megger model which doesn't seem available any more. Individual conductors are only accessible in the CU, not sure if you could get the clamp in there. Splitting cables doesn't seem an easy option?
 
Maybe the idea is a flexible adapter, a hoop you can unplug and pass behind the conductor and then re-plug, pushing the banana plugs at the other end of the adapter into your multimeter. Not cheap at £100+ though.
 
Individual conductors available in every socket. on a ring final the same current(ish) will be at every socket.
But there’s usually room for a clamp meter in the CU, One of the line conductors going into the MCB Is the usual place. There’s usually a short loop at that point.
 
No, you won’t get any current there.
Unscrew the socket and access the conductors behind. But better and more accurate inside the consumer unit.
 
Take socket front off, clamp meter on live conductor. Don't do it using a 13A plug top as you will only see the current that the plugged in device is using.
 
Callcom said:
Had a look at clamp meters, great solution except you can only clamp individual conductors - apart from a Megger model which doesn't seem available any more. Individual conductors are only accessible in the CU, not sure if you could get the clamp in there. Splitting cables doesn't seem an easy option?
Click to expand...
I have 1 of those Megger clamps handy bit of kit.
 
Thanks for the suggestions, some good ones there. CU might be the best bet, though space is a little limited. I also thought you needed to avoid close proximity to other conductors as that might affect the magnetic field. I'll go for the cheap clamp meter off Amazon and experiment - though as I say there's been no tripping at all so far even with the system under reasonably high load (I'm not looking forward to the bill though..)
 
Callcom said:
Thanks for the suggestions, some good ones there. CU might be the best bet, though space is a little limited. I also thought you needed to avoid close proximity to other conductors as that might affect the magnetic field. I'll go for the cheap clamp meter off Amazon and experiment - though as I say there's been no tripping at all so far even with the system under reasonably high load (I'm not looking forward to the bill though..)
Click to expand...
This is what you need, might find one on ebay, I still have mine.
http://www.biddlemegger.com/biddle-ug/Flexiclamp_200_UG.pdf
 
Thanks again for the suggestions, I'll have a look at the Flexiclamp.
Yes that's right about the 'efficiency' claims. I got the impression that Haverland were suggesting they could produce more heat per amp, but how you would measure that I'm not sure, without some sort of comparison. They certainly chuck out the heat and no-one's been cold, but as I say we'll see what the elec bill is like before celebrating.
 
Can't find a Flexiclamp 200 anywhere, even Ebay. I guess one might come up sometime, in the meantime I'll go for the cheapo Amazon one - thanks Taylortwocities for the advice re ohter influences
 
Callcom said:
Can't find a Flexiclamp 200 anywhere, even Ebay. I guess one might come up sometime, in the meantime I'll go for the cheapo Amazon one - thanks Taylortwocities for the advice re ohter influences
Click to expand...
Still got mine?
 
shaun1 said:
Or you can clamp the live meter tail to get total current. And then switch on one circuit at a time to see individual circuit currents.
Click to expand...

Which is a far more sensible suggestion than messing around trying to get a clamp meter into a consumer unit, or measure half the current at a socket!
 
Taylortwocities said:
Individual conductors available in every socket. on a ring final the same current(ish) will be at every socket.
But there’s usually room for a clamp meter in the CU, One of the line conductors going into the MCB Is the usual place. There’s usually a short loop at that point.
Click to expand...

There’s an obvious problem with this suggestion, and other methods of measurement are safer to carry out.
 
While is still cold ,could become a human smart meter , taking two readings 6 hours apart , when you think its the coldest !
( dress appropriately - It's not one of those reality torture shows)
..we will not know the Volts for sure .....,
but have a 10% guess at amps average
 
Last edited:
Last edited:
Next issue - even in this weather, with electric heaters on a lot, no tripping at all. But - we are looking at heating the pool, which would take at least 15Kw elec heater (no gas/oil). There is a 60a supply (single phase) to pool house which drives pump and heat exchanger (which apparently only heats pool sufficiently on a few (hot) days of year).

House has 100a supply, pretty heavily used as heating is electric. Any thoughts as to solution? How feasible to add a 3-phase supply or convert to? Cheers
 
New posts

Reply to Potential overload of ring mains in the UK Electrical Forum area at ElectriciansForums.net

Similar Threads

S
Attic sockets in ring main uk
Hi all I would like to put some sockets in the attic and keep them on the main house ring main. Am I right in saying I can pull one of the legs...
Replies
1
Views
250
Markyd
Markyd
N
RING MAIN CONFUSION
Hi guys. Having a weird problem in a house that has suddenly happened. One half of the ring main has 240ish volts (fluctuates of course), and...
Replies
9
Views
519
pc1966
P
C
Help with spurs from ring main
Good evening. Currently sorting out my girlfriend’s flat for rent. I’ve found all sorts of bad electrical work. Can anyone advise if this is an...
Replies
18
Views
1K
Callumh1992
C
M
Extending ring mains on top of plaster
Essentially I have a "normal" socket in a ring mains, i.e. one 2.5mm T&E going in and one 2.5mm T&E going out. I am looking to simply add two more...
Replies
2
Views
360
Mjward
M
I
UK Kitchen grid switch help
Hello everyone, I'd like to seek your input on a matter. I'm in the process of designing the electrical connections for the following kitchen...
Replies
38
Views
3K
ibra123
I

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electrical Goods - Electrical Tools - Brand Names Pushfit Wire Connectors Electric Underfloor Heating Electrician Courses
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

YOUR Unread Posts

Tags

advice aus cable circuit course earth electric electrical electrician hello led light lighting lights looking new please question rcd socket supply switch testing training wiring
This website was designed, optimised and is hosted by untold.media Operating under the name Untold Media since 2001.
Tiling Advice
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock