Kitchen Unit Lights to LightSwitch - Help Appreciated

[Risteard]

"553-04 Lighting points
553-04-01 At each fixed lighting point one of the following accessories shall be used:
(i) a ceiling rose to BS 67
(ii) a luminaire supporting coupler to BS 6972 or BS 7001
(iii) a batten lampholder to BS 7895, BS EN 60238 or BS EN 61184
(iv) a luminaire designed to be connected directly to the circuit wiring
(v) a suitable socket-outlet
(vi) a connection unit to BS 5733 or BS 1363-4.
A lighting installation shall be appropriately controlled, e.g. by a switch or combination of switches to BS 3676 and/or BS 5518, or by a suitable automatic control system, which where necessary shall be suitable for discharge lighting circuits.
553-04-02 A ceiling rose shall not be installed in any circuit operating at a voltage normally exceeding 250 volts.
553-04-03 A ceiling rose shall not be used for the attachment of more than one outgoing flexible cord unless it is specially designed for multiple pendants.
553-04-04 Luminaire supporting couplers are designed specifically for the mechanical support and electrical connection of luminaires and shall not be used for the connection of any other equipment."

So who's to say that you don't adopt 553-04-01(v), and install "a suitable socket-outlet" to the lighting circuit, as a lighting point, for supplying lights (or whatever). Reasonable labelling (and / or reasonable location, e.g. at high level) should help overcome the temptation to plug heavy current using equipment into it (thereby avoiding nuisance trips); it would be hard to argue that such a labelled / located socket outlet, even if it is to BS1363, is not a "a suitable socket-outlet". Also,553-04-01(vi) refers to "a connection unit to...BS 1363-4", which is a standard Fused Connection Unit.

Those are 16th Edition format Regulation numbers.

 

[Pete999]

Those are 16th Edition format Regulation numbers.

On the ball there Mate well spotted

 

[Toneyz]

Callum, are you going to reply to my post?

 

[Spoon]

Callum, are you going to reply to my post?

I'm sure he will, as the OP is a wonderful bloke who take on all advice given........

 

[KEV 1 N]

Time for this me thinks......

 

[Pete999]

Callum, are you going to reply to my post?

Doubtful Ant very doubtful

 

[GeorgeCooke]

P.S Here is a link to the transformer i am looking at. Is this suitable?

LED Driver Transformer DC 12v-6w, 10W 12w, 18w, 30w,40W for MR11, MR16 LED Strip | eBay - https://www.ebay.co.uk/itm/LED-Driver-Transformer-DC-12v-6w-10W-12w-18w-30w-40W-for-MR11-MR16-LED-Strip/291227662579?hash=item43ce8578f3:m:m1oUI8fA_qqZMfaQKe59ytA

None of those are transformers, ebay are lying. Transformers are AC devices, they never produce DC. They are LED DC power supplies.

 

[Spoon]

Time for this me thinks......
View attachment 39996

I like that... haha

 

[Des 56]

Design a project that you are unsure about
Put forward that project for scrutiny by others
Take note of well informed advice that's offered and ignore
Fill in knowledge gaps(trawl obsolete papers on the subject)
Make attempt to justify the proposed design with random guesswork


Why would you anyone need electrical training when its all so simple

 

[Colin33]

Lets all demonise this muppet for even considering doing his own electrics. If people can't afford to pay a sparkie's often exorbitant rate then what the hell do we expect them to do? Any electrician looking at that old wilex board will run a mile! I certainly wouldn't work on/add to any circuit coming from an unprotected supply like that. So what do we do? Tell him to p!ss off or offer a little advice on how he can achieve what he wants to do? I thought that part of the purpose of a forum like this was to help and advise people....