Kitchen Unit Lights to LightSwitch - Help Appreciated

[Octopus]

^^

To help and advise fellow sparks

Not

Clueless DIYers ....

 

[Toneyz]

Maybe the OP should of not told a forum member to get off the post and not insulting others he would have got better advice. I asked him a few questions of which he chose not to do so, therefore, I could not advise/help further.

 

[Colin33]

If that's the case then why are 'clueless diyers' allowed to join the forum? Do you think the forum should be restricted to those with electrical qualifications only?

 

[Toneyz]

Colin33 Everything I put in the post above was true of this post and his previous post on the same subject that's why he got the replies he did.If he engaged and answered the questions that I asked I could have given a solution the OP could then decided if he felt competent in undertaking the correct work. I don't have a problem with DIY'ers doing basic electrical work as long as they know their limitations.There is a DIY part of the electrical forum.Maybe you should offer some advice to the OP which you have not done so far.I have with respect to you Colin as a forum member revised my rating to disagree for the reasons above of which I hope you would reciprocate.
PS some of us only ask for a fair rate for the work undertaken and are not there to rip customers off we have to charge a rate that covers our costs in undertaking the work.

 

[Gavin John Hyde]

my option although i dont condone him doing it himself would be to add a spur off one of the existing sockets and install a double rcd socket that can feed the plugs that hopefully are still attached, this could be placed in top of a floor level unit so as to be accessible . this spur could be supplied by a fcu at another point to give a switch / isolation point. it also gives him rcd protection for the alteration and then avoids a fuse board upgrade.. However, i suspect he will likely bodge it and then decide to get somebody in after it goes wrong...

 

[Colin33]

Colin33 Everything I put in the post above was true of this post and his previous post on the same subject that's why he got the replies he did.If he engaged and answered the questions that I asked I could have given a solution the OP could then decided if he felt competent in undertaking the correct work. I don't have a problem with DIY'ers doing basic electrical work as long as they know their limitations.There is a DIY part of the electrical forum.Maybe you should offer some advice to the OP which you have not done so far.I have with respect to you Colin as a forum member revised my rating to disagree for the reasons above of which I hope you would reciprocate.
PS some of us only ask for a fair rate for the work undertaken and are not there to rip customers off we have to charge a rate that covers our costs in undertaking the work.

Of course I will reciprocate in this instance, I'm sure you can understand why I'm not happy with being rated 'dumb' for simply expressing an opinion! I would've offered the OP some advice, had the original post not been blocked before I had read it. I read these forums less often than I used to because I'm often almost embarrassed by some of my 'fellow electricians' who relish trying to humiliate diy'ers who are simply after advice which may help them achieve a safer outcome than they would without that advice. Some of the contributors of this thread were clearly not willing to help OP, so perhaps should not get involved because their remarks were not helpful and did nothing to dispel the general feeling that many electricians are over paid arrogant To&&ers!

 

[Spoon]

Hi @Colin33 . The OP was given solutions what would have been safe. He chose not to take then on board. He wanted to use a new switch he had fitted but what he suggested was again going against the regs.
I feel that the OP is not competent enough to carry out the electrical work.
I have helped out many DIY posts. I have asked them questions and they have answered them. When I feel that will do the job to regs and not ignore my advice I then give it.

 

[Pete999]

Lets all demonise this muppet for even considering doing his own electrics. If people can't afford to pay a sparkie's often exorbitant rate then what the hell do we expect them to do? Any electrician looking at that old wilex board will run a mile! I certainly wouldn't work on/add to any circuit coming from an unprotected supply like that. So what do we do? Tell him to p!ss off or offer a little advice on how he can achieve what he wants to do? I thought that part of the purpose of a forum like this was to help and advise people....

Hi Colin 33, I gave my disagree label, solely because it is not my policy to yell amateurs and DIYers like the OP step by step instructions, he obviously hadn't a clue of the dangers of what he was attempting, as for demonising the OP I consider he demonised himself from the word go, on both posts he posted on the same theme, I hope that goes some way to explain my "disagree"

 

[Colin33]

Hi Pete, you're welcome to 'disagree' it'd be a boring place if we all agreed with each other It's the 'dumb' option that I take offence to! I'm not even sure why we have such a condescending option amongst purported professionals, or is in place to be used to humiliate the diy'ers? Maybe the Mod can explain this one.

 

[Pete999]

Lets all demonise this muppet for even considering doing his own electrics. If people can't afford to pay a sparkie's often exorbitant rate then what the hell do we expect them to do? Any electrician looking at that old wilex board will run a mile! I certainly wouldn't work on/add to any circuit coming from an unprotected supply like that. So what do we do? Tell him to p!ss off or offer a little advice on how he can achieve what he wants to do? I thought that part of the purpose of a forum like this was to help and advise people....

Hi Colin 33, I gave my disagree label, solely because it is not my policy to yell amateurs and DIYers like the OP step by step instructions, he obviously hadn't a clue of the dangers of what he was attempting, as for demonising the OP I consider he demonised himself from the word go, on both posts he posted on the same theme, I hope that goes some way to explain my "disagree"

Hi Pete, you're welcome to 'disagree' it'd be a boring place if we all agreed with each other It's the 'dumb' option that I take offence to! I'm not even sure why we have such a condescending option amongst purported professionals, or is in place to be used to humiliate the diy'ers? Maybe the Mod can explain this one.

Have you asked the poster "why the dumb" check on the profile, you may find he knows SFA