fcu by kitchen sink

[dal_87]

hi would like some info regarding fitting fcu near kitchen sink. now i know as good practice it should be min 300mm away from edge of sink horizontally , but in a job iam doin tomorrow i require to go vertical. does this still stand ? iam installing a hot water urn in a staff kitchen in a college, the kitchen is small and the supply will have to be above the sink area ...can i (A) just install fcu above with min 300mm or (B) look to install fcu near ceiling and drop down in a flex outlet plate .. all will be surface mounted .. looking for some guidance thanks in advance

 

[Leesparkykent]

I think you just have to be practical...probably not best to install the fused spur out of reach but not in a position its going to be splashed etc.

 

[dal_87]

thanks for the reply makes sense just did not want to do something incorrect .... so maybe i just install fcu above sink at a decent height where it will not get splashed

 

[Leesparkykent]

thanks for the reply makes sense just did not want to do something incorrect .... so maybe i just install fcu above sink at a decent height where it will not get splashed

That's what I would do.

 

[Octopus]

Interestingly BS7671 does not quote any distances.

Another glaring issue with our regs!

 

[Simonslimline]

Some scenarios just require the common sense approach.

 

[bigspark17]

I would say min 600mm from tap. Tin hat on

 

[atm84]

As Murdoch states in post 5 bs7671 doesn't state a min distance from a sink. Although guidance documents such as Ekectricians guide to the building regs suggest 300mm. At the end of the day that is only guidance and you need to be pragmatic using your professional judgement


Sent from my iPhone using Tapatalk

 

[Andy78]

Interestingly BS7671 does not quote any distances.

Another glaring issue with our regs!

The regs make clear that all equipment must be suitable for the location and any environmental influences likely to be encountered in that location. If it's not suitable then it shouldn't be installed. Common sense and the discretion of the designer and/or installer is all that is needed.

 

[Octopus]

The regs make clear that all equipment must be suitable for the location and any environmental influences likely to be encountered in that location. If it's not suitable then it shouldn't be installed. Common sense and the discretion of the designer and/or installer is all that is needed.

Which so many people lack these days.....

 

[Simonslimline]

Which so many people lack these days.....

The thing about common sense is that it's not very common.

 

[snowhead]

Which so many people lack these days.....

They're brought up with so many fluffy cushions around them nowadays they don't have the chance to acquire common sense

 

[Andy78]

Which so many people lack these days.....

True. If it wasn't for the odd few being so dumb we wouldn't need the constant dumbing down of the regulations and society in general.

I do feel that this is an area of the regs that does not need specific guidance as the general rules cover the installation of equipment, it's use, and it's environment adequately.

 

[ian.settle1]

Which so many people lack these days.....

It died when the PC crowd started opening their mouths

 

[Dave OCD]

As this is a kitchen area in a college used by lots of different people I'd consider using an IP rated switched FCU the same as those used externally.

 

[atm84]

Stick it on an rcd and use an ip rated FCU then everyone will be happy. On another note; doesn't anyone called them switched fused spurs anymore?


Sent from my iPhone using Tapatalk

 

[slingshot2000]

On another note; doesn't anyone called them switched fused spurs anymore?

Yes, I do !

 

[andyb]

And me.

 

[Dave OCD]

Me too but best to avoid anything but exactly correct terminology on here or you can get ripped to shreds.

 

[atm84]

Me too but best to avoid anything but exactly correct terminology on here or you can get ripped to shreds.

Haha I know what you mean. The way everyone goes around on here you expect everyone speaking true IET language on site

 

[andyb]

Me too but best to avoid anything but exactly correct terminology on here or you can get ripped to shreds.

What's the exactly correct terminology then Dave?

 

[Dave OCD]

What's the exactly correct terminology then Dave?

You tell me ? :juggle:

 

[Simonslimline]

Fused connection unit. Switched fused connection unit. Or a fused spur thingy bob.?