Omission of overload protection for fixed loads.

[Darkwood]

Its funny how this thread i set up has consequently bounced around all the main Electrical forums lol.... Again! You'd think that on the IET forum the regulation architects would see this repeated confusing issue and subsequently amend it to either make it clearer or address the domestic situe with a cover note on this regulation.

My take on this is if the regs were simple to follow then the IET wouldn't make any money on their little franchise in on site guides... conspiracy theory!

 

[Engineer54]

Its funny how this thread i set up has consequently bounced around all the main Electrical forums lol.... Again! You'd think that on the IET forum the regulation architects would see this repeated confusing issue and subsequently amend it to either make it clearer or address the domestic situe with a cover note on this regulation.

My take on this is if the regs were simple to follow then the IET wouldn't make any money on their little franchise in on site guides... conspiracy theory!

The Reg's havent been written in plain English since the 14th ed!! Now it needs umpteen OSG's to give readers a clue of what it's saying!! lol!!

 

[telectrix]

The heater manufacturers will have to comply to their own BS standards, the flex will be compatible for the load of the heater so they won't be responsible, clearly the issue here is a connection problem or a failed FCU by matter of interest i bet the multi-stranded cable termination into the fcu wasn't appropriately crimped for termination so if so then the installers fault, if it was down to failure of the FCU then the FCU manufacturers fault, proving it and laying blame isn't usually worth the hassle on a simple repair. For your query regarding using 433.3 they are not subject to the BS7671 but thats not to say they dont have this regulation in their own BS standards as clearly they have omitted overload protection of the flex itself. Having said this this wasn't caused by overload but thermal conductivity from a poor contact or connection in the FCU which regardless of any overload protection this would have created the same effect even with a fuse rated spot on for the load.

agree entirely. the 2 things are not related. my call out was to the damaged termination in the FCU. just didn't like the fact that a 2kW heater was running on 0.75mm flex with a 13A fuse. i would have expected 1.0mm at least.

 

[Darkwood]

Your probably refering to CCC of flex in the BS7671 i deal will many different kinds of flex and its misleading the it might seem too small been 0.75 but different brands and constructs of the insualtion and sheath give some cables a higher CCC comparable to say a 1.0mm standard pvc flex.

 

[Outspoken]

circuit diagrams are your friend here.

there are many of them available via google, and I've just checked several to be sure. Regardless of that though, the point you were making is wrong as even an overheating element won't add more than 0.2% or so to the load of the circuit.

Sorry for the late reply, took advantage of some clear weather today to take the ankle biters out...till it ruddy rained anyway!

Anyway, I checked our shower thoroughly, and can confirm the following are installed;

2 x Thermocouples
1 x manual reset bimetal thermal sensor
1 x Pressure transducer
1 x flow sensor
1 x overload sensor (magnetic)

Based on this I have to concur will all comments by Gavin and initially by DW. With this level of protection in the unit then realistically an RCD protecting the Unit would be sufficient for compliance with the Regs at the basic fault protection level, although personally I would still, if I installed a shower, use a correctly rated RCBO to cover both bases.

Many thanks Guys, It's always good to learn and I love things that make me investigate and perhaps, as in this case, change how I think about something...Nice one.

 

[Toonlad]

Round of applause, good read, good interpretation, and very good technical knowledge. :clap::clap::clap: Still dont know what it all means lmao.

My personal take on most domestics this day, is far to many sparks just put in a certain size of cable and circuit breaker, as its the norm for that type of circuit. Ask them why a particular size and they will answer, Thats what the regs state or thats what i was tought.

 

[Stroppy]

Lights = 1mm
Sockets/Immersion = 2.5
Shower/cooker = 6.

Easy!

 

[Guest55]

Round of applause, good read, good interpretation, and very good technical knowledge. :clap::clap::clap: Still dont know what it all means lmao.

My personal take on most domestics this day, is far to many sparks just put in a certain size of cable and circuit breaker, as its the norm for that type of circuit. Ask them why a particular size and they will answer, Thats what the regs state or thats what i was tought.

to be honest thats the whole point of the OSG , a wire by numbers book for the domestic installers.
;-)

 

[Gavin A]

Sorry for the late reply, took advantage of some clear weather today to take the ankle biters out...till it ruddy rained anyway!

Anyway, I checked our shower thoroughly, and can confirm the following are installed;

2 x Thermocouples
1 x manual reset bimetal thermal sensor
1 x Pressure transducer
1 x flow sensor
1 x overload sensor (magnetic)

Based on this I have to concur will all comments by Gavin and initially by DW. With this level of protection in the unit then realistically an RCD protecting the Unit would be sufficient for compliance with the Regs at the basic fault protection level, although personally I would still, if I installed a shower, use a correctly rated RCBO to cover both bases.

Many thanks Guys, It's always good to learn and I love things that make me investigate and perhaps, as in this case, change how I think about something...Nice one.

fair play.

 

[Darkwood]

Does that mean i win this round then outspoken :bucktooth: lol only joking ...... if it causes differing opinions then it serves its purpose as a thread and we all learn regardless of whether initially the OP is wrong or not.... we are taught the basics but not interpretation and i find this site is a gem for changing how you see things ...yes ive been wrong many times too :!blank:

 

[Outspoken]

Totally agree DW, if we can debate and use our collective experience to make life a little better for all then that is a success. I do not see such debates about winning or losing, unless we allow it to iterate into a slanging match, as you see on other sites, and then we all lose.

 

[Edd]

Interesting Thread, Now im wiring a 9kw shower, gona back it up by a 40 A MCB... Ref method 103 and 101 as im going up through a insulated wall and across the loft... Now What cable shall I use!!! (page 340).. Dam Thats gona be fun squeezing in a 45A D/P switch!!!

 

[Outspoken]

Interesting Thread, Now im wiring a 9kw shower, gona back it up by a 40 A MCB... Ref method 103 and 101 as im going up through a insulated wall and across the loft... Now What cable shall I use!!! (page 340).. Dam Thats gona be fun squeezing in a 45A D/P switch!!!

Claim you only did the 5 week course and use a bit of 4.0mm² SWA!!

 

[Gavin A]

for reference, I just checked, and this method is allowed under both BS7671 and MCS guide for solar PV installations, though I'd not realised it was before - it's actually spelled out in the new PV guide.

In very many cases the current limiting nature of the PV array and inverter(s) omits the requirements for overload protection and therefore the designer only need to consider fault current protection.

Only thing is, I'm a little wary about relying entirely on the suppliers fuse for fault protection, as would be the case if we were installing to a henley block on the tails, as it would blow the power for the entire house if there were a fault, and need the supplier calling out to replace fuse (technically anyway).

 

[Edd]

edited...

 

[Engineer54]

I this tread still going!! lol!!

 

[Darkwood]

I this tread still going!! lol!!

Exactly how drunk was you when you wrote this! :smartass2:

 

[Engineer54]

Exactly how drunk was you when you wrote this! :smartass2:

I'm not that much of a drinker actually, unless were talking coffee!!!! But i can, i suppose put it down to advancing years!! ...lol!!

 

[Darkwood]

I'm not that much of a drinker actually, unless were talking coffee!!!! But i can, i suppose put it down to advancing years!! ...lol!!

Have a chat with Marvo! ..... after his senile thread i think there's an opportunity to open a new club on .... maybe a 'Well past the post' club :sick:

 

[Engineer54]

Have a chat with Marvo! ..... after his senile thread i think there's an opportunity to open a new club on .... maybe a 'Well past the post' club :sick:

That's not very kind, ......On Marvo!! lol!! Another excuse i can latch onto, was that it was early in the morning, ...and hadn't yet got to my second morning coffee!! lol!!