is tht Grey/Grey to comply with harmonisation?
 
  • Like
Reactions: Dave OCD
Thank god there’s no ferrules on the 6mm conductors going into the rcbo, the YouTube gang would be furious with you Dave.
 
Great job!
 
  • Like
Reactions: Dave OCD
All you guys recommending tape, have you never heard of Hot Glue??
 
Thank god there’s no ferrules on the 6mm conductors going into the rcbo, the YouTube gang would be furious with you Dave.
Believe it or not they are ferruled Ian, just hard to see in the picture. And to quote Jim Royle , I couldn't give a shiny sh1te about the YouTube gang. ?
 
Believe it or not they are ferruled Ian, just hard to see in the picture. And to quote Jim Royle , I couldn't give a shiny sh1te about the YouTube gang. ?
1616356848935.gif
 
  • Like
Reactions: Dave OCD and DPG
Believe it or not they are ferruled Ian, just hard to see in the picture.
Indeed, close inspection shows the uninsulated ferrules used! Neat.

Also the originals are not soldered - that is a big no-no for screw terminals as it compresses with time and becomes loose - but it is an ultrasonic weld. Basically squashed it to sold again.
 
  • Like
Reactions: Dave OCD and DPG
Looks good. Did MK make the devices? Look a bit MK like in terms of their interpretation of vertical.
The key to overcoming the MK slant is a quick release ratchet clamp, grip the mcbs, rcds and main switch etc then fit busbars. everything then sits nice and vertical without the slant.
 
The key to overcoming the MK slant is a quick release ratchet clamp, grip the mcbs, rcds and main switch etc then fit busbars. everything then sits nice and vertical without the slant.

Theres a gap in the market for a VDE rated ratchet clamp then ?
 
i Quite like the MK lean , you wouldn’t try to straighten the leaning tower of pisa.
the lean is part of its charm
 
  • Funny
Reactions: Dave OCD
Newlec lean too.
DFED865C-84B5-4C11-A86A-B6980403ED65.jpeg


The Hager mcb was a recent addition by a Fischer Heat installer. Don’t know whether to bring it up
 
Right hand side. There’s an LHS on other rcd.
In the house, it’s more front and rear of the house. One room has sockets on two circuits on opposite walls. (I know, not an issue, just mentioning)

Whatever happened to upstairs downstairs?
 
  • Agree
Reactions: Dave OCD
Right hand side. There’s an LHS on other rcd.
In the house, it’s more front and rear of the house. One room has sockets on two circuits on opposite walls. (I know, not an issue, just mentioning)

Whatever happened to upstairs downstairs?
Hudson retired.
 
Right hand side. There’s an LHS on other rcd.
In the house, it’s more front and rear of the house. One room has sockets on two circuits on opposite walls. (I know, not an issue, just mentioning)

Whatever happened to upstairs downstairs?
It's a way of saving cable, two halves of the house incorporating upstairs and downstairs instead of running a ring all the way round twice. It can be a pain for accurate labelling though and most of the lazy buggers just write 'sockets' with no more detail.
 
  • Like
Reactions: nicebutdim and DPG
It's a way of saving cable, two halves of the house incorporating upstairs and downstairs instead of running a ring all the way round twice. It can be a pain for accurate labelling though and most of the lazy buggers just write 'sockets' with no more detail.

I have never been a fan on this left hand right hand way of wiring sockets, I have come across houses where you have sockets and legs of rings all interconnected all over the place. Having a socket fed from 2 mcbs sets my spider senses into over drive. And 2 sockets in the same room on different circuits sets my ocd off
 
I did an EICR today which included 5 socket circuits in an average 3 bed house. 4 of these circuits were rings and all were just labelled sockets, so I had to check exactly what went where and label accordingly - one RFC served just two sockets in a bedroom !
 
  • Like
Reactions: pc1966 and DPG

Similar threads

OFFICIAL SPONSORS

Electrical Goods - Electrical Tools - Brand Names Electrician Courses Green Electrical Goods PCB Way Electric Underfloor Heating Electrician Courses Heating 2 Go Electrician Workwear Supplier
These Official Forum Sponsors May Provide Discounts to Regular Forum Members - If you would like to sponsor us then CLICK HERE and post a thread with who you are, and we'll send you some stats etc

Advert

Daily, weekly or monthly email

Thread starter

Dave OCD

Mentor
Esteemed
Arms
~
Joined
Location
Cornwall
If you're a qualified, trainee, or retired electrician - Which country is it that your work will be / is / was aimed at?
United Kingdom
What type of forum member are you?
Practising Electrician (Qualified - Domestic or Commercial etc)
Business Name
Hendry Electrical Services

Thread Information

Title
'Real World' CU upgrade.
Prefix
N/A
Forum
UK Electrical Forum
Start date
Last reply date
Replies
39

Advert

Thread statistics

Created
Dave OCD,
Last reply from
pc1966,
Replies
39
Views
4,369

Advert